User manual TOSHIBA TDP-T250

[. . . ] TDP-T250 OWNER'S MANUAL DATA PROJECTOR Others Maintenance Operations Preparations Before Using Before Using SAFETY PRECAUTIONS Before Using 3 The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING: Handling the cord on this product or cords associated with accessories sold with USA only this product, will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. [. . . ] If the lamp overheats, it may fail to light, and its lifetime will be shortened. 26 27 Operations Basic operations 1 Turn on the power. Turn on the power by following the instructions in "Turning the power on" p. 26 . 5 Projector placement angle adjustments The placement angle and the height of the projected image can be adjusted by the foot adjuster. 2 Select the language and the lamp power (When using the first time). When the projector is used for the first time after purchase, the start menu for language (to display the menus and messages on the screen) and lamp power selection and configuration is displayed in English. (If the screen is out of focus, adjust it according to the step 6 . ) q Lift up the front of the projector to the desired angle, then press the foot adjuster release button. The foot adjuster extends. Release the button to lock the position. q Use the or button to select the desired language and press the button. Message for setup confirmation is displayed in a selected language. Then, the menu for lamp power selection and configuration is displayed. To change the setting, follow the step w. w Use the or button to select the lamp power and press the button. The lamp power, if selected, will be toggled without pressing the button. The display automatically disappears in a few seconds. Notes · When the projector is turned on the next time, the start menu does not appear upon startup. However, if [Reset all] is executed from the Default setting menu p. 44 , the start menu will be displayed the next time when the power is turned on. · The language can also be set via the Display setting menu p. 41 and Lamp power via the Default setting menu p. 44 . · This owner's manual assumes that English has been selected. 7 Adjusting the volume with the Notes buttons The speaker volume can be adjusted when an audio signal is being input. 3 Activate the connected device. Turn on and start the connected device such as a computer. 4 Press the INPUT button. An image of the connected eqipment is projected. Each time you press the INPUT button, it switches to the input of the connected equipment that is outputting video signals. Notes · When [Auto input search] is set to [On] in the Default setting menu p. 44 (factory setting is [On]), the input is switched to the connected equipment that is outputting video signals each time you press the INPUT button p. 45 . · If no signal is being output from the connected equipment, pressing the INPUT button does not change the input and "There is no other input signal. " will appear. · Note that a lamp characteristics may rarely cause the brightness to fluctuate slightly. If used for extended periods, images will appear dark, and the lamp could burn out. (The lifetime of the lamp depends on conditions of use. ) · The DMDTM is made using extremely advanced technology, but there may be black spots (pixels that do not light) or bright spots (pixels that are constantly lit) on the panel. · Although this projector supports a wide range of RGB signals p. 56 , any resolutions not supported by this projector (XGA) will be expanded or shrunk, which will affect image quality slightly. To view high-quality images, it is recommended that the computer's external output should be set to XGA resolution. · With some models of computer having LCD displays or the like, displaying images simultaneously on the projector and the monitor's display may prevent the images from displaying properly. For information on how to turn off the LCD display, see the owner's manual of your computer. · If no signal is being input from the connected equipment or signal input is stopped while projecting, the "No signal" will appear. · If a signal not supported by the projector is input, the "Unsupported signal" will appear. · If an unavailable operation button is pressed, the icon will appear. 28 29 Operations English French German Italian Spanish Portuguese Russian Swedish Turkish Polish Japanese Chinese (simplified) Chinese (traditional) Korean w To fine adjust the angle, twist the foot adjuster. e To adjust the horizontal angle, use the tilt adjuster. To stow the foot adjuster, hold up the projector while pressing the foot adjuster release button, then slowly lower the projector. 6 Adjusting the screen size and focus q Use the zooming lever to adjust the screen size. w Use the focusing lever to adjust the focus. Using handy features Using auto setting (Only for analog input from computer) This function sets up the projector to the optimum state such as sampling phase, frequency, screen position, and clamp for each type of the input signal by using simple operations. Remote Control Adjusting vertical distortion [Auto] 2 Press the button. The keystone distortion is automatically corrected. [. . . ] p. 29 Is the projection distance within the projector's supported range?p. 39 Image is dark Colors too light Bad shading · Are the brightness or contrast adjustments off?p. 48 · · · · Are the color, tint, R-level, G-level, or B-level adjustments off?p. 44 Control panel key doesn't work Connection terminal Picture not displayed correctly · Is the input signal supported by the projector? [. . . ]