User manual TOSHIBA TDP-S35

[. . . ] OWNER'S MANUAL DATA PROJECTOR (SVGA / With Document Camera) Others Maintenance Operations Preparations TDP-S35 TDP-SC35 (SVGA) Before Using Before Using SAFETY PRECAUTIONS Before Using The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING: Handling the cord on this product or cords associated with accessories sold with USA only this product, will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. [. . . ] Attempting to clean/replace the lamp at a high site by yourself may cause you to drop down, thus resulting in injury. · If you wish to mount the projector on the ceiling, be sure to ask your dealer to do so. Mounting the projector on a ceiling requires special ceiling brackets (sold separately) and specialized knowledge. Improper mounting could cause the projector to fall, resulting in an accident. · If the projector is ceiling-mounted, install the breaker for turning off the power in case of anomaly. Let everyone involved with the use of the projector know that fact. Audio cable (not supplied) Control cable Video cable (not supplied) CONTROL MONITOR S-VIDEO AUDIO OUT R L VIDEO COMPUTER 2 IN ( Y/PB/PR ) AUDIO IN COMPUTER 1 IN ( Y/PB/PR ) Projection Distance and Size Use the figures, tables, and formulas below to determine the projection size and projection distance. (Projection sizes are approximate values for full-size picture with no keystone adjustment. ) Screen RGB cable (not supplied) To audio output White (L)/ Red (R) Audio cable (not supplied) AV cable (not supplied) To video output As seen from above a (min length) = projection size (inches) 28. 571 To RGB output 90° Audio cable (not supplied) projection size (inches) a (max length) = 24. 631 To audio output RGB cable (supplied with TDP-SC35) To audio output RGB cable (supplied) To RGB output VCR Monitor cable Mini D-sub 15P-BNC (not supplied) To Y/CB/CR output Green (Y)/Blue (CB)/Red (CR) As seen from the side Lens center projection size (cm) 40 (102) 60 (152) 80 (203) 100 (254) 150 (381) 200 (508) 250 (635) 300 (762) H 90° a a is the distance (m) between the lens and the screen, and corresponds to a range of 1. 26 m to 10. 5 m. H is the height from the image bottom to the center of the lens. projection distance a (m) height (H) min length max length (cm) (zooming max) (zooming min) 1. 4 1. 62 4. 0 2. 1 2. 44 5. 9 2. 8 3. 25 7. 9 3. 5 4. 06 9. 9 5. 25 6. 09 14. 9 7. 0 8. 12 19. 8 8. 75 10. 15 24. 8 10. 5 -- 29. 7 Conversion adapter BNC-pin (not supplied) Computer Document camera Computer DVD video recorder, etc. Notes · COMPUTER terminals 1 and 2 function identically. · For TDP-SC35, the document camera should be connected to COMPUTER terminal 2. · The AUDIO IN terminal doubles for devices connected to COMPUTER terminals 1 and 2. 20 21 Preparations Operations Turning the power on and off Connecting the power cord Notes · The start-up screen will disappear after a moment. You can dismiss the start-up screen before this by performing any operation. You can also configure the start-up screen not to appear via the Display setting menu p. 31 . · The first time you use the projector after purchase, after the start-up screen disappears, the Language menu is displayed p. 24 . 1 Insert the power cord connector into the AC IN socket of the projector. Insert the power cord plug into a wall or (Supplied) Power cord connector other power outlet. 2 Removing the lens cover Be sure to remove the lens cover when the power is turned on. If it is left on, it could become deformed due to heat. Turning the power off 1 Press the ON/STANDBY button. A message appears on the screen, confirming that you wish to shut off the power. (This operation is no longer valid after the message disappears. ) 2 Turning the power on Press the ON/STANDBY button again. The screen turns off, but the internal cooling fan continues to operate for a short while. Then, the projector goes into standby mode. 1 Turn on the main power switch The ON indicator will change to orange, indicating standby mode. TEMP LAMP FAN When cooling lamp TEMP LAMP FAN (Green) During internal cooling TEMP LAMP (Off) After cooling complete TEMP LAMP (Off) FAN (Green) FAN (Off) 2 Press the ON/STANDBY button. The power turns on, and the following 3 green indicators light: ON, LAMP, and FAN. After a moment, the start-up screen appears. Control panel Remote Control Start-up screen B (Orange) C (Orange) A During cooling, the LAMP indicator flashes. After the LAMP indicator goes off, the cooling fan continues to operate for a short while, in order to expel excess internal heat. If you are in a hurry, there is no problem with unplugging the power cord or turning off the main power switch in this state. In standby mode B C Note CAUTION · Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes or sight. [. . . ] one minute of abnormal display, the projector returns to the standby state waiting for internal cool down. TDP-SC35 TEMP LAMP FAN Power went out during use (Green lit) (Red lit) PRECAUTION · Make sure to unplug the power cord if something goes wrong. 40 41 Others Camera is not correctly connected. · Disconnect the power plug and check the connection with the camera. one minute of abnormal display, the projector returns to the standby state waiting for internal cool down. Before calling service personnel If you think something is wrong, check the followings before contacting customer service. If This Happens No power Power goes out during use No picture Check · Is the power cord plugged in? [. . . ]