User manual TOSHIBA TDP-MT700

[. . . ] English Owner's Manual Home Theater Projector TDP-MT700 SAFETY PRECAUTION The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING: Handling the cord on this projector, or the cords associated with accessories sold with this projector, will expose you to lead, a chemical known to the State of California to cause birth USA only defects or other reproductive harm. [. . . ] Make sure the Power light is orange after power has been applied and the main AC power switch is turned on. Press and hold the ON/STANDBY button on the projector or remote control to turn the projector on. The ON/STANDBY button may not work while the projector is warming up. 3. "Searching. . . . " will display on-screen before the projector identifies the input signal. If the horizontal frequency of the input signal exceeds the range of the projector, a message reading "Unsupported timing" will display on-screen. This message will remain on-screen until you change the input signal. Switching input signals The projector can be connected to multiple devices at the same time. To sequentially select input signals, press one of the INPUT buttons on the remote control or INPUT on the projector. When the projector is turned on, it will search for the input source you last selected. If you need to use the PIP or POP function, refer to p. 23 for advanced operation. CAUTION · Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes or sight. · Do not place your hands, face, or other objects near the air exhaust. Doing so could cause burns, deform/break the object. 20 Using the projector and remote control English Adjust the image Adjusting the angle height Turn the two feet on the bottom of the projector to adjust the image height and projection angle (see illustration at right). If the screen and the projector are not perpendicular to each other, the projected image becomes distorted (trapezoidal). To correct this problem, adjust the Keystone value in the Setup menu. Auto-adjusting the image When you press the Auto button on the projector, the built-in intelligent auto-adjustment function will readjust the values of Frequency and Clock to provide the best image quality. The current source information will display at the bottom right cornor of the screen for 3 seconds. The screen will be blank while the auto-adjustment is functioning. Fine-tuning the image size and clarity 1. Then sharpen the image by rotating the focus ring. Optimizing the image To optimize the image, use the remote control or on-screen menus. It depends on the image quality you desire. Note · Note that a lamp characteristics may rarely cause the brightness to fluctuate slightly. If used for extended periods, images will appear dark, and the lamp could burn out. (The lifetime of the lamp depends on conditions of use. ) · The DMDTM is made using extremely advanced technology, but there may be black spots (pixels that do not light) or bright spots (pixels that are constantly lit) on the panel. Please note that these are not malfunctions. Using the projector and remote control 21 1. Selecting a picture mode Select a picture mode on the remote control (or in the Picture > Load Settings menu). The following four modes are available for each input, with preset values suitable for various projection purposes: Dynamic Standard Theater 1 Theater 2 You also can customize the picture settings by adjusting the functions in the Picture menu, and save those settings as USER MEMORY 1, 2, or 3. Selecting a Screen Size The aspect ratio is the ratio of image width to image height. Change the image ratio using the SCREEN SIZE buttons on the remote control (or in the Display > Screen Size menu). [. . . ] --- Flashing Green Off Off Cannot turn on the projector. When the projector is in an abnormal state: POWER TEMP LAMP State (1) The lamp has exceeded its usage life. · Please contact your dealer for assistance. Solution: Orange Off Red · Make sure the ventilation holes are not blocked. · The intake ventilation or the · Relocate the projector. · Stop using the projector until · The projector may be in a the ambient temperature poorly ventilated location. [. . . ]