User manual TOSHIBA TDP-MT200

[. . . ] English Français Español Deutsch Italiano Português Svenska OWNER'S MANUAL DLPTM PROJECTOR Others Maintenance Operations Preparations TDP-MT200 Before Using Before Using SAFETY PRECAUTIONS The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING: Handling the cord on this product or cords associated with accessories sold with USA only this product, will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. [. . . ] Improper mounting could cause the projector to fall, resulting in an accident. · If the projector is ceiling-mounted, install the breaker for turning off the power in case of anomaly. Let everyone involved with the use of the projector know that fact. Projection Distance and Size Use the figures, tables, and formulas below to determine the projection size and projection distance. (Projection sizes are approximate values for full-size picture with no keystone adjustment. ) Screen As seen from above a (min length) = projection size (inches) × 0. 0414 a (max length) = projection size (inches) × 0. 0498 projection distance a (m) height (H) min length max length (cm) (zooming max) (zooming min) -- 1. 20 16 1. 66 1. 99 27 2. 48 2. 99 40 3. 31 3. 98 53 4. 14 4. 98 67 6. 21 7. 47 100 8. 28 9. 96 134. 4 12. 00 -- 195 90° As seen from the side Lens center projection size (cm) 24. 1 (61) 40 (102) 60 (152) 80 (203) 100 (254) 150 (381) 200 (508) 290 (736) H 90° a a is the distance (m) between the lens and the screen, and corresponds to a range of 1. 20 m to 12. 00 m. H is the height from the image bottom to the center of the lens. 19 Preparations Connection Before connection · Read the owner's manual of the device you are connecting to the projector. · Some types of computer cannot be used or connected to this projector. This does not mean that all of these devices can or must be connected simultaneously. (Dotted lines mean items can be exchanged. ) Computer (for control) Video recorder, DVD player, etc. VCR, etc To RS-232C terminal p. 43 Control cable To S-Video output S-Video cable (supplied) To video output Video cable (supplied) RGB component video cable (not supplied) To Y/CB/CR output Green (Y)/Blue (CB)/Red (CR) DVI cable (not supplied) RGB cable (not supplied) To DVI output DVD video recorder, etc. To RGB output Computer Computer Notes · If you want to feed the digital RGB signal, separately available DVI cable is needed. · If you are using the digital RGB signal for input to this unit, some computer models or a certain type of DVI cable may cause on rare occasions noise on the screen. If such is a case, decrease your computer's refresh rate or the resolution. It is also recommended to use a DVI cable in 2 m or less in length. 20 English Français Español Deutsch Italiano Português Svenska Connecting the power cord 1 2 Insert the power cord connector into the AC IN socket of the projector. Insert the power cord plug into a wall or other power outlet. Power cord connector (Supplied) Removing the lens cover Turning the power on 1 Turn on the main power switch The ON indicator will change to orange, indicating standby mode. · After the main power switch is turned on, the inner cooling fan starts cooling. (Orange) 2 Press the ON/STANDBY button. The power turns on, and the following 3 green indicators light: ON, LAMP, and FAN. After a moment, the start-up screen appears. Control panel Remote Control Start-up screen CAUTION · Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes or sight. · Do not place your hands, face, or other objects near the air exhaust. Doing so could cause burns, deform/break the object. 21 Preparations Be sure to remove the lens cover when the power is turned on. If it is left on, it could become deformed due to heat. Turning the power on and off (Continued) Notes · The start-up screen will disappear after a moment. You can dismiss the start-up screen before this by performing any operation. You can also configure the start-up screen not to appear via the Display setting menu p. 30 . · The first time you use the projector after purchase, after the start-up screen disappears, the Language menu is displayed p. 23 . Turning the power off 1 Press the ON/STANDBY button. A message appears on the screen, confirming that you wish to shut off the power. (This operation is no longer valid after the message disappears. ) 2 Press the ON/STANDBY button again. The screen turns off, but the internal cooling fan continues to operate for a short while. [. . . ] If This Happens No power Power goes out during use No picture Check · Is the power cord plugged in?· · · · · p. 23 p. 36 Is the projector turned on?p. 20 Are all the connected devices functioning properly? Picture not displayed correctly Picture blurred Part of picture out of focus · Is the input signal supported by the projector?p. 39 , p. 40 , p. 41 · Is there something generating an abnormal video signal, for instance the video tape? [. . . ]