User manual TOSHIBA TDP-FF1

[. . . ] OWNER'S MANUAL LED PROJECTOR TDP-FF1A Before Using Operations Others Preparations SAFETY PRECAUTIONS The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING: Handling the cord on this product or cords associated with accessories sold USA only with this product, will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. [. . . ] Normal mode: · When OSD is not displayed: Volume control (Computer, Video input) · When OSD is displayed: Choose menu item File view mode: · When OSD is not displayed: Choose file or directory · When OSD is displayed: Choose menu item Slideshow mode: · Show previous/next slide Normal mode: · When OSD is not displayed: AUTOSET (RGB signal) · When OSD is displayed: Confirm screen menu selections File view mode: · When OSD is not displayed: Highlight on a file: Start the slideshow Highlight on a directory: Change the directory · When OSD is displayed: Confirm screen menu selections Slideshow mode: · To pause or re-start the slide show 2. <, > + 3. AUTOSET / 18 Remote control keypad and functions Remote Control 8 7 6 5 1 2 3 4 1. AUTOSET 2. Auto set Normal mode: · When OSD is not displayed: No action · When OSD is displayed: Confirm screen menu selections File view mode: · When OSD is not displayed: Highlight on a file: Start the slideshow Highlight on a directory: Change the directory · When OSD is displayed: Confirm screen menu selections Slideshow mode: · To pause or re-start the slide show Adjust volume Correct image distortion Pause image (Computer, Video input only) Display menu system/move to upper level in menu system Normal mode: · When OSD is not displayed: No action · When OSD is displayed: Choose menu item File view mode: · When OSD is not displayed: Choose file or directory · When OSD is displayed: Select screen menu items Slideshow mode: · Show previous/next slide Select input sources 3. Input 19 Preparations Using the battery pack with the projector The following procedures are for the installation of the battery pack with the projector. Installing the battery Turn off the power switch and disconnect the AC adaptor. Plug in the battery pack. Press down the battery pack firmly until it clicks into place. Switch the power button to turn on the projector. Remove the battery Turn off the power switch and disconnect the AC adaptor. Close the battery connector cover. 2 1 3 Charge the battery The battery pack can be charged with the projector when the AC adaptor is connected. It takes 3 to 4 hours to charge the battery completely. 20 Notes · Remove the battery if the projector is not in use, otherwise the battery will gradually discharge. · When the battery capacity become less then 10%, the following message appears: The battery capacity is less than 10%. · Press any key to make the warning message disappear. · When the projector runs out of the battery, it shuts down automatically after showing the message "The projector is shutting down". · The projector will work for approximate 2 hours with full charged battery at room temperature (25°C). · The battery is consumables, it can be recharged approximately 500 times. · It is recommended that you replace to a new battery when the operation time with the battery becomes significantly short. (contact reseller for details) · Do not touch the battery connector. Before taking it to the center, stick insulating tape to the terminal. Specifications for TOSHIBA Li-ion battery · Model name: TLPBP1 · Output voltage: 7. 4V · Capacity: 4400mAh · Operating temperature: 5°~35°C (41°~95°F) · Dimensions: 138(W)x56(H)x26(D) mm · Weight: 0. 25kg · Always observe the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when handling the battery. Warning 21 Preparations Using the remote control Changing the new lithium battery Remove the battery compartment. Replace the lithium battery. Insert the battery compartment. Be sure to align the battery according to the polarity. Operating the remote control Note Turn on the projector and then the remote control can be used to adjust the OSD, volume, and input select. · The remote control is shipped with a plastic sheet between the battery and its contact. · Remove the battery from the remote control when it will not be used for an extended period. Battery · Before using the battery, please refer to the notes on . · If the remote control stops working, or if its range decreases, replace the battery with new one. · The remote control may fail to operate if the infrared remote sensor is exposed to bright sunlight or fluorescent lighting. · In rare cases, ambient conditions could impede the operation of the remote control. If this happens, point the remote control at the main unit again, and repeat the operation. The remote control 22 Placement Placement Styles The factory setting is "floor-mounted front projection. " Set the [Projection mode] in the Default setting menu , in accordance with your needs. · Always observe the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when placing the unit. Warning Projection Distance and Size Screen Top view a (min length) = projection size (inches) 27. 3403 FF1 uses a fixed lens. projection size (inches) 11 17 25 30 35 40 45 50 60 68 projection distance (m) 0. 40 0. 62 0. 91 1. 10 1. 28 1. 46 1. 65 1. 83 2. 19 2. 49 height (H) (cm) 1. 7 2. 6 3. 8 4. 6 5. 3 6. 1 6. 9 7. 6 9. 1 10. 4 Side view Lens center Note: 110% offset condition a is the distance (m) between the lens and the screen, and corresponds to a range of 0. 4 m to 2. 5 m. H is the height from the image bottom to the center of the lens. 23 Preparations Use the figures, tables, and formulas below to determine the projection size and projection distance. [. . . ] Description Input source name Resolution (in dots) Display color method of video signal Display the battery remains Firmware version [Note] RGB Yes Yes No Yes Yes Y/PB/PR Yes No Yes Yes Yes "Yes": displayed, "No": not displayed Video Yes No Yes Yes Yes USB Yes No No Yes Yes 39 Operations 2. [Firmware version] shows the version of the projector's internal control program. This version is referred to for customer service, etc. Lens and main unit cleaning Lens cleaning · Clean the lens with a commercially available blower and/or lens cleaner. · The lens is easily scratched, so do not rub it with hard objects, or strike it. Main unit cleaning · Clean the main unit after unplugging the power cord. [. . . ]