User manual TOSHIBA SELECT

[. . . ] 1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 System overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Capacity compensation chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Piping requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Refrigerant cycle diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Sensible capacity table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Part load performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 10 Wiring guideline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 11 Wiring diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inner circuit 12 Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 13 Fan characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133 A. [. . . ] If there is an obstacle above the outdoor unit, ensure there is a minimum space of 2000mm or more above the unit. Any obstacle around the perimeter of the outdoor unit must be kept 800mm or less. Draw out the locally supplied piping at the front of the outdoor unit horizontally, keep a minimum of 500mm or more. between the outdoor unit and traversing pipe If the pipework is to be installed in this method. _ _ (Header > Follower 2 > Follower 3 ) 990 20 or more 990 20 or more 990 700 anchor bolt pitch (310) 700 anchor bolt pitch (310) 700 anchor bolt pitch 1 2 3 12-15 x 20 (Long hole) 1800 1640 88 700 165 3010 Combination unit MMY-AP2201T8, HT8, HT7 MMY-AP2401T8, HT8, HT7 MMY-AP2601T8, HT8, HT7 MMY-AP2801T8, HT8, HT7 MMY-AP3001T8, HT8, HT7 MMY-AP3221T8, HT8, HT7 MMY-AP3411T8, HT8, HT7 MMY-AP3611T8, HT8, HT7 Combination outdoor unit Header MMY-MAP0801T8, HT8, HT7 MMY-MAP0801T8, HT8, HT7 MMY-MAP1001T8, HT8, HT7 MMY-MAP1001T8, HT8, HT7 MMY-MAP1001T8, HT8, HT7 MMY-MAP1201T8, HT8, HT7 MMY-MAP1201T8, HT8, HT7 MMY-MAP1201T8, HT8, HT7 (Note 3) 600 (1000 or more) (Note 4) or more 600 or more 500 or more Follower MMY-MAP0801T8, HT8, HT7 MMY-MAP0801T8, HT8, HT7 MMY-MAP0801T8, HT8, HT7 MMY-MAP1001T8, HT8, HT7 MMY-MAP1001T8, HT8, HT7 MMY-MAP1001T8, HT8, HT7 MMY-MAP1201T8, HT8, HT7 MMY-MAP1201T8, HT8, HT7 (Rear side) Follower MMY-MAP0601T8, HT8, HT7 MMY-MAP0801T8, HT8, HT7 MMY-MAP0801T8, HT8, HT7 MMY-MAP0801T8, HT8, HT7 MMY-MAP1001T8, HT8, HT7 MMY-MAP1001T8, HT8, HT7 MMY-MAP1001T8, HT8, HT7 MMY-MAP1201T8, HT8, HT7 (Note 4) (Note 3) (Note 4) (1000 or more) 500 or more 600 or more 500 or more (Note 4) 500mm or more Front side Front side Front side Front side Front side Front side 1750mm or more 500mm or more Front side Front side Front side Front side Front side Front side 10mm or more 20mm or more 20mm or more Front side (For work and service) (Front side) 750 755 anchor bolt pitch 790 (including steady leg) 10mm or more 500 or more Front side Front side Front side 3030mm or more 15 Space required for service 800 or less 800 or less 183 Four units connected MMY-AP3201T8, AP3401T8, AP3601T8, AP3801T8, AP4001T8, AP4201T8, AP4401T8, AP4601T8, AP4801T8 MMY-AP3201HT8, AP3401HT8, AP3601HT8, AP3801HT8, AP4001HT8, AP4201HT8, AP4401HT8, AP4601HT8, AP4801HT8 MMY-AP3201HT7, AP3401HT7, AP3601HT7, AP3801HT7, AP4001HT7, AP4201HT7, AP4401HT7, AP4601HT7, AP4801HT7 990 20 or more 990 20 or more 990 20 or more 990 700 anchor bolt pitch (310) 700 anchor bolt pitch (310) 700 (310) anchor bolt pitch 700 anchor bolt pitch 16-15 x 20 (Long hole) 4 1 165 2 3 1800 1640 88 700 4020 Combination unit MMY-AP3201T8, MMY-AP3401T8, MMY-AP3601T8, MMY-AP3801T8, MMY-AP4001T8, MMY-AP4201T8, MMY-AP4401T8, MMY-AP4601T8, MMY-AP4801T8, HT8, HT8, HT8, HT8, HT8, HT8, HT8, HT8, HT8, HT7 HT7 HT7 HT7 HT7 HT7 HT7 HT7 HT7 Combination outdoor unit Follower Follower MMY-MAP0801T8, HT8, HT7 MMY-MAP0801T8, MMY-MAP0801T8, HT8, HT7 MMY-MAP0801T8, MMY-MAP1001T8, HT8, HT7 MMY-MAP0801T8, MMY-MAP1001T8, HT8, HT7 MMY-MAP1001T8, MMY-MAP1001T8, HT8, HT7 MMY-MAP1001T8, MMY-MAP1001T8, HT8, HT7 MMY-MAP1001T8, MMY-MAP1201T8, HT8, HT7 MMY-MAP1001T8, MMY-MAP1201T8, HT8, HT7 MMY-MAP1201T8, MMY-MAP1201T8, HT8, HT7 MMY-MAP1201T8, Header MMY-MAP0801T8, MMY-MAP1001T8, MMY-MAP1001T8, MMY-MAP1001T8, MMY-MAP1001T8, MMY-MAP1201T8, MMY-MAP1201T8, MMY-MAP1201T8, MMY-MAP1201T8, HT8, HT8, HT8, HT8, HT8, HT8, HT8, HT8, HT8, HT7 HT7 HT7 HT7 HT7 HT7 HT7 HT7 HT7 HT8, HT8, HT8, HT8, HT8, HT8, HT8, HT8, HT8, HT7 HT7 HT7 HT7 HT7 HT7 HT7 HT7 HT7 Follower MMY-MAP0801T8, MMY-MAP0801T8, MMY-MAP0801T8, MMY-MAP0801T8, MMY-MAP1001T8, MMY-MAP1001T8, MMY-MAP1001T8, MMY-MAP1001T8, MMY-MAP1201T8, 800 or less (Note 4) 500mm or more 500mm or more 10mm or more 20mm or more 20mm or more 20mm or more 10mm or more Front side (For work and service) 4040mm or more Space required for service 184 1750mm or more 15 800 or less (NOTES) 1. If there is an obstacle above the outdoor unit, ensure there is a minimum space of 2000mm or more above the unit. Any obstacle around the perimeter of the outdoor unit must be kept 800mm or less. Draw out the locally supplied piping at the front of the outdoor unit horizontally, keep a minimum of 500mm or more. between the outdoor unit and traversing pipe If the pipework is to be installed in this method. _ _ Header > Follower 2 > _ Follower 3 > Follower 4 (Note 3) (Note 4) (1000 or more) (Note 4) 500 or more 600 or more 500 or more (Note 4) (Note 3) (1000 or more) 500 600 600 or more or more or more Front side Front side Front side Front side Front side Front side Front side Front side Front side Front side Front side Front side Front side Front side Front side Front side 500 or more Front side Front side Front side Front side ( ) 750 755 anchor bolt pitch 790 (including steady leg) HT8, HT8, HT8, HT8, HT8, HT8, HT8, HT8, HT8, HT7 HT7 HT7 HT7 HT7 HT7 HT7 HT7 HT7 Branch header/Branch joint Branch header RBM-HY1043E, HY1083E, HY2043E, HY2083E Gas side B 80 x n A 50 Insulator Liquid side B 80 x n A B C Insulator Model RBM-HY1043E RBM-HY1083E Gas side Liquid side Gas side Liquid side Gas side Liquid side Gas side Liquid side 74. 5 , Accessory soket Q ty 6 x 4, 9 x 4, 14 x 1, 18 x 1, 70 x 1 1 x 4, 6 x 1, 9 x 1 6 x 8, 9 x 8, 14 x 1, 18 x 1, 70 x 1 1 x 8, 6 x 1, 9 x 1 6 x 2, 9 x 2, 27 x 1, 59 x 1 1 x2 6 x 7, 9 x 7, 27 x 1, 59 x 1 1 x7 A 380 360 700 680 385. 5 360 705. 5 680 B 90 60 90 60 95. 5 60 95. 5 60 C 83. 6 _ 83. 6 _ 89. 3 _ 89. 3 _ OD / OE / n 3 3 7 7 3 3 7 7 22. 2 15. 9 22. 2 15. 9 31. 8 15. 9 31. 8 15. 9 15. 9 9. 5 15. 9 9. 5 15. 9 9. 5 15. 9 9. 5 RBM-HY2043E RBM-HY2083E T-shape branch joint RBM-BT13E Gas side O 38. 1 / O 22. 2 / O 9. 5 / Liquid side Balance pipe 14 10 26 39 61 O 38. 1 / O 38. 1 / O 22. 2 / O 22. 2 / O 9. 5 / 10 14 78 14 52 10 7 32 7 O 9. 5 / 7 13 15 , Accessory soket Q ty Gas side Liquid side 61 x 1, 62 x 1, 71 x 2, 73 x 2, 74 x 1, 14 x 2, 18 x 1, 85 x 2, 86 x 1 185 Y-shape branch joint RBM-BY53E, BY103E Gas side Liquid side OD / OC / OB / OC / OD / OD / Insulator Insulator A A RBM-BY203E, BY303E Gas side Liquid side OD / OC / OC / B OD / OD / OD / Insulator A Insulator A Model RBM-BY53E Gas side Gas side Gas side Gas side 250 350 350 80 70 80 80 80 80 80 15. 9 12. 7 12. 7 9. 5 22. 2 19. 1 15. 9 12. 7 31. 8 28. 6 15. 9 15. 9 22. 2 19. 1 Liquid side 200 Liquid side 250 Liquid side 250 Liquid side 350 , Accessory soket Q ty 5 x 2, 54 x 2, 9 x 1, 51 x 1 1 x 2, 5 x 1 7 x 1, 10 x 1, 13 x 2, 18 x 1, 52 x 2, 70 x 1, 89 x 1 2 x 1, 5 x 2, 6 x 1, 9 x 1, 54 x 1 16 x 1, 20 x 1, 27 x 1, 43 x 2, 48 x 1, 49 x 1, 58 x 1, 59 x 1 3 x 1, 6 x 1, 9 x 2 61 x 3, 62 x 2, 71 x 2, 73 x 1, 74 x 1, 75 x 1, 76 x 1, 77 x 1 4 x 1, 7 x 1, 10 x 1, 13 x 2, 14 x 1, 18 x 1, 52 x 1 15 RBM-BY103E RBM-BY203E RBM-BY303E 400 110 38. 1 38. 1 186 OD / B B Accessory socket 1 2 5 54 O6. 4 / OB / 24 A A 2 5 OB / 29 6. 4 26 9. 5 31 15. 9 O9. 5 / Outer dia O12. 7 / 54 Outer dia 3 6 9 51 4 7 10 13 52 89 OB / OB / 4 A 7 OB / 39 6. 4 39 9. 5 36 12. 7 33 15. 9 43 22. 2 53 28. 6 A 3 6 9 OB / 35 6. 4 32 9. 5 28 12. 7 38 19. 1 A 10 13 52 A O15. 9 / 51 O19. 1 / 89 Outer dia Outer dia 14 18 70 85 86 16 20 43 48 49 58 OB / 14 A 18 70 85 OB / OB / 16 20 A OB / 40 15. 9 40 19. 1 41 12. 7 44 9. 5 50 15. 9 52 19. 1 50 22. 2 54 9. 5 52 12. 7 62 34. 9 A A 54 28. 6 43 48 49 O22. 2 / 86 Outer dia O28. 6 / 58 Outer dia 27 59 61 62 73 74 75 76 77 A 61 62 71 73 OB / OB / OB / 55 34. 9 66 41. 3 66 28. 6 66 22. 2 66 19. 1 64 15. 9 62 12. 7 62 9. 5 A 74 75 76 A 27 OB / 49 28. 6 59 34. 9 O31. 8 / 59 A 15 O38. 1 / 77 Outer dia Outer dia 187 188 16 Specifications 189 Foreword 190 16 Specifications Foreword TECHNICAL SPECIFICATIONS Indoor unit (50Hz specification) 4-way Air Discharge Cassette Type Model name Cooling/Heating capacity (Note 1) Power supply Electrical characteristics Running current (A) 50Hz MMU- AP0091H AP0121H AP0151H AP0181H AP0241H AP0271H AP0301H AP0361H AP0481H AP0561H (kW) 2. 8/3. 2 3. 6/4. 0 4. 5/5. 0 5. 6/6. 3 7. 1/8. 0 8. 0/9. 0 9. 0/10. 0 11. 2/12. 5 14. 0/16. 0 16. 0/18. 0 1 phase 50Hz 230V (220 - 240V) (Separate power supply for indoor units is required. ) 0. 17 0. 020 0. 30 0. 19 0. 022 0. 33 0. 21 0. 026 0. 36 0. 24 0. 032 0. 42 0. 35 0. 048 0. 59 0. 59 0. 070 0. 87 0. 81 0. 110 1. 23 0. 83 0. 112 1. 26 Power consumption (kW) Starting current Main unit (A) Heat-insulating material attached Zinc hot dipping steel plate Model Panel colour Height (mm) (mm) (mm) (mm) (mm) (mm) (kg) (kg) 20 22 4. 5 Finned tube Non-flammable insulation Turbo fan 800 (730/680) 930 (830/790) 1, 050 (920/800) 60 Standard filter (Long life filter) Remote controller 1, 200 (920/820) 1, 320 1, 680 2, 040 2, 090 (1, 110/850) (1, 300/1, 070) (1, 430/1, 130) (1, 520/1, 230) 90 RBC-U21PG (W) -E Moon white (Munsell/2. 5GY 9. 0/0. 5) 256 840 840 35 950 950 23 28 319 Appearance Ceiling Panel Main unit Width Outer dimension Ceiling panel Depth Height Width Depth Main unit Total weight Ceiling panel Heat exchanger Soundproof/Heat-insulating material Fan Fan unit Standard air flow High (m3/h) (Mid. /Low) Motor (W) Air filter Controller Gas side Connecting Liquid side pipe (mm) (mm) O 9. 5 / O 6. 4 / O 12. 7 / O 15. 9 / O 9. 5 / Drain port (Nominal dia. mm) Sound pressure level(Note 2) (High/Mid. /Low) (dB(A)) 30/29/27 31/29/27 25 (Polyvinyl chloride tube) 32/29/28 34/31/28 37/33/30 40/36/33 44/38/34 45/40/34 Note 1 : The cooling capacities and electrical characteristics are measured under the conditions specified by JIS B 8615 based on the reference piping. Normally, the values measured in the actual operating environment become larger than the indicated values due to the effects of external sound. Note : Rated conditions Cooling : Indoor air temperature 27 C DB/19 C WB, Outdoor air temperature 35 C DB Heating : Indoor air temperature 20 C DB, Outdoor air temperature 7 C DB/6 C WB O O O O O O 16 195 50Hz Under Ceiling Type Model name Cooling/Heating capacity (Note 1) Power supply Running current (A) 0. 29 0. 033 0. 43 MMC(kW) AP0151H 4. 5/5. 0 AP0181H 5. 6/6. 3 AP0241H 7. 1/8. 0 AP0271H 8. 0/9. 0 AP0361H 11. 2/12. 5 AP0481H 14. 0/16. 0 1 phase 50Hz 230V (220 - 240V) (Separate power supply for indoor units is required. ) 0. 32 0. 038 0. 48 0. 42 0. 050 0. 62 White (Munsell 10Y 9. 3/0. 4) 0. 78 0. 091 1. 17 0. 84 0. 110 1. 25 Electrical characteristics Power consumption (kW) Starting current (A) Appearance Outer dimension Height x Width x Depth (mm) Total weight Heat exchanger Soundproof/Heat-insulating material Fan Standard air flow (High/Mid. /Low) Motor Controller Room thermostat Air filter Gas side Connecting Liquid side pipe (mm) (mm) O 12. 7 / O 6. 4 / 210 x 910 x 680 22 210 x 1, 180 x 680 26 Finned tube Non-flammable insulation Centrifugal fan 210 x 1, 595 x 680 34 (kg) Fan unit (m3/h) (W) 720/600/540 30 780/660/540 1, 110/900/840 40 Remote controller Attached Standard filter (Long life filter) 1, 650/1, 380/1, 2001, 800/1, 560/1, 320 80 O 15. 9 / O 9. 5 / Drain port (Nominal dia. mm) Sound pressure level(Note 2) (High/Mid. /Low) (dB(A)) 35/32/30 36/33/30 20 (Polyvinyl chloride tube) 38/36/33 41/38/35 43/40/37 Note 1 : The cooling capacities and electrical characteristics are measured under the conditions specified by JIS B 8615 based on the reference piping. The reference piping consists of 5 m of main piping and 2. 5 m of branch piping connected with 0 meter height. Note 2 : The sound levels are measured in an anechoic chamber in accordance with JIS B8616. Normally, the values measured in the actual operating environment become larger than the indicated values due to the effects of external sound. Note : Rated conditions Cooling : Indoor air temperature 27 C DB/19 C WB, Outdoor air temperature 35 C DB Heating : Indoor air temperature 20 C DB, Outdoor air temperature 7 C DB/6 C WB O O O O O O 16 196 50Hz High Wall Type Model name Cooling/Heating capacity (Note 1) Power supply Running current Power consumption Starting current Suction grille and side panel Appearance Discharge grille Bottom surface Outer dimension Total weight Heat exchanger Soundproof/Heat-insulating material Fan Fan unit Standard air flow (High/Mid. /Low) Motor outlet Air filter Controller Gas side Connecting pipe Liquid side (mm) (mm) O 9. 5 / O 6. 4 / MMK(kW) AP0071H 2. 2/2. 5 AP0091H 2. 8/3. 2 AP0121H 3. 6/4. 0 AP0151H 4. 5/5. 0 AP0181H 5. 6/6. 3 AP0241H 7. 1/8. 0 1 phase 50Hz 230V (220 - 240V) (Separate power supply for indoor units is required. ) (A) (kW) (A) 0. 30 0. 035 0. 36 Silky mist (Munsell 1Y 8. 9/0. 5) City gray (Munsell N6. 5) Silky mist (Munsell 1Y 8. 9/0. 5) (mm) (kg) 368 x 895 x 210 18 Finned tube Non-flammable insulation Cross-flow fan (m3/h) (W) 600/540/480 30 Standard filter (Simple filter) Remote controller O 12. 7 / O 15. 9 / O 9. 5 / Electrical characteristics 0. 32 0. 037 0. 42 0. 35 0. 040 0. 47 Height x Width x Depth 368 x 1, 055 x 210 19 368 x 1, 430 x 210 25 780/660/600 1, 200/1, 020/900 Drain port (Nominal dia. mm) (dB(A)) 39/34/31 20 (Polyvinyl chloride tube) 42/38/35 42/38/35 Sound pressure level(Note 2) (High/Mid. /Low) Note 1 : The cooling capacities and electrical characteristics are measured under the conditions specified by JIS B 8615 based on the reference piping. The reference piping consists of 5 m of main piping and 2. 5 m of branch piping connected with 0 meter height. Note 2 : The sound levels are measured in an anechoic chamber in accordance with JIS B8616. Normally, the values measured in the actual operating environment become larger than the indicated values due to the effects of external sound. [. . . ] CDB 10. 0 12. 0 14. 0 16. 0 18. 0 20. 0 21. 0 23. 0 25. 0 27. 0 29. 0 31. 0 33. 0 35. 0 37. 0 39. 0 10. 0 12. 0 14. 0 16. 0 18. 0 20. 0 21. 0 23. 0 25. 0 27. 0 29. 0 31. 0 33. 0 35. 0 37. 0 39. 0 14. 0CWB 20CDB TC SHC 3. 7 3. 7 3. 7 3. 7 3. 7 3. 7 3. 7 3. 7 3. 7 3. 7 3. 7 3. 7 3. 7 3. 7 3. 6 3. 5 4. 6 4. 6 4. 6 4. 6 4. 6 4. 6 4. 6 4. 6 4. 6 4. 6 4. 6 4. 6 4. 6 4. 6 4. 5 4. 3 2. 8 2. 8 2. 8 2. 8 2. 8 2. 8 2. 8 2. 8 2. 8 2. 8 2. 8 2. 8 2. 8 2. 8 2. 7 2. 7 3. 5 3. 5 3. 5 3. 5 3. 5 3. 5 3. 5 3. 5 3. 5 3. 5 3. 5 3. 5 3. 5 3. 5 3. 3 3. 3 16. 0CWB 23CDB TC SHC 4. 1 4. 1 4. 1 4. 1 4. 1 4. 1 4. 1 4. 1 4. 1 4. 1 4. 1 4. 1 4. 1 4. 1 4. 0 3. 8 5. 1 5. 1 5. 1 5. 1 5. 1 5. 1 5. 1 5. 1 5. 1 5. 1 5. 1 5. 1 5. 1 5. 1 4. 9 4. 8 3. 0 3. 0 3. 0 3. 0 3. 0 3. 0 3. 0 3. 0 3. 0 3. 0 3. 0 3. 0 3. 0 3. 0 2. 9 2. 8 3. 7 3. 7 3. 7 3. 7 3. 7 3. 7 3. 7 3. 7 3. 7 3. 7 3. 7 3. 7 3. 7 3. 7 3. 6 3. 5 TC : Total capacity [kW] Indoor air temp. 18. 0CWB 19. 0CWB 20. 0CWB 26CDB 27CDB 28CDB TC SHC TC SHC TC SHC 4. 4 4. 4 4. 4 4. 4 4. 4 4. 4 4. 4 4. 4 4. 4 4. 4 4. 4 4. 4 4. 4 4. 4 4. 2 4. 1 5. 4 5. 4 5. 4 5. 4 5. 4 5. 4 5. 4 5. 4 5. 4 5. 4 5. 4 5. 4 5. 4 5. 4 5. 3 5. 1 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 1 3. 0 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 8 3. 7 4. 5 4. 5 4. 5 4. 5 4. 5 4. 5 4. 5 4. 5 4. 5 4. 5 4. 5 4. 5 4. 5 4. 5 4. 4 4. 2 5. 6 5. 6 5. 6 5. 6 5. 6 5. 6 5. 6 5. 6 5. 6 5. 6 5. 6 5. 6 5. 6 5. 6 5. 4 5. 3 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 1 3. 0 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 8 3. 7 4. 6 4. 6 4. 6 4. 6 4. 6 4. 6 4. 6 4. 6 4. 6 4. 6 4. 6 4. 6 4. 6 4. 6 4. 5 4. 4 5. 8 5. 8 5. 8 5. 8 5. 8 5. 8 5. 8 5. 8 5. 8 5. 8 5. 8 5. 8 5. 8 5. 8 5. 6 5. 4 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 1 3. 0 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 8 3. 7 SHC : Sensible capacity [kW] 22. 0CWB 30CDB TC SHC 4. 9 4. 9 4. 9 4. 9 4. 9 4. 9 4. 9 4. 9 4. 9 4. 9 4. 9 4. 9 4. 9 4. 9 4. 7 4. 6 6. 1 6. 1 6. 1 6. 1 6. 1 6. 1 6. 1 6. 1 6. 1 6. 1 6. 1 6. 1 6. 1 6. 1 5. 9 5. 7 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 2 3. 1 3. 0 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 9 3. 7 3. 6 24. 0CWB 32CDB TC SHC 5. 1 5. 1 5. 1 5. 1 5. 1 5. 1 5. 1 5. 1 5. 1 5. 1 5. 1 5. 1 5. 1 5. 1 5. 0 4. 8 6. 4 6. 4 6. 4 6. 4 6. 4 6. 4 6. 4 6. 4 6. 4 6. 4 6. 4 6. 4 6. 4 6. 4 6. 2 6. 0 3. 1 3. 1 3. 1 3. 1 3. 1 3. 1 3. 1 3. 1 3. 1 3. 1 3. 1 3. 1 3. 1 3. 1 3. 0 2. 9 3. 8 3. 8 3. 8 3. 8 3. 8 3. 8 3. 8 3. 8 3. 8 3. 8 3. 8 3. 8 3. 8 3. 8 3. 7 3. 6 015 018 A-39 13 5. Wiring diagrams MMD-AP0071SPH(SH), AP0091SPH(SH), AP0121SPH(SH), AP0151SPH(SH), AP0181SPH(SH) 14 A-40 6. Fan characteristics MMD-AP0071SPH MMD-AP0091SPH Standard air volume : 540m3/h 60 MMD-AP0121SPH Standard air volume : 600m3/h 60 High (50Pa) 50 Upper limit of external static pressure(50Pa) High (50Pa) 50 Upper limit of external static pressure(50Pa) External static pressure (Pa) 40 High (35Pa) External static pressure (Pa) Upper limit of external static pressure(35Pa) High (35Pa) 40 Low (50Pa) Upper limit of external static pressure(35Pa) Low (35Pa) Lower limit of external static pressure (50Pa) High (20Pa) 30 Upper limit of external static pressure(20Pa) Low (50Pa) Lower limit of external static pressure (50Pa) High (20Pa) 30 20 Upper limit of external static pressure(10Pa) Low (35Pa) Lower limit of external static pressure (35Pa) High (10Pa) 20 Upper limit of external static pressure(20Pa) Lower limit of external static pressure (35Pa) High (10Pa) 10 Low (20Pa) Lower limit of external static pressure (20Pa) Low (10Pa) 10 Low (20Pa) Upper limit of external static pressure(10Pa) Low (10Pa) Lower limit of external static pressure (20Pa) 0 300 400 500 600 700 0 300 400 500 600 700 Air Volume (m3/h) Air Volume (m3/h) MMD-AP0151SPH MMD-AP0181SPH Standard air volume : 690m3/h 60 60 Standard air volume : 780m3/h High (50Pa) Upper limit of external static pressure(50Pa) High (50Pa) 50 50 Upper limit of external static pressure(50Pa) External static pressure (Pa) External static pressure (Pa) 40 Upper limit of external static pressure(35Pa) High (35Pa) High (35Pa) 40 Low (50Pa) 30 Low (50Pa) Lower limit of external static pressure (50Pa) 30 Upper limit of external static pressure(35Pa) Low (35Pa) High (20Pa) Lower limit of external static pressure (50Pa) High (20Pa) 20 20 Low (35Pa) Lower limit of external static pressure (35Pa) High (10Pa) Upper limit of external static pressure(20Pa) Upper limit of external static pressure(10Pa) 10 Upper limit of external static pressure(20Pa) Lower limit of external static pressure (35Pa) Low (20Pa) Lower limit of external static pressure (20Pa) 10 Low (20Pa) Lower limit of external static pressure (20Pa) Low (10Pa) Upper limit of external static pressure(10Pa) Low (10Pa) High (10Pa) 0 400 500 600 700 800 0 400 500 600 700 800 900 Air Volume (m3/h) Air Volume (m3/h) A-41 15 6. [. . . ]