User manual TOSHIBA SATELLITE C660D

[. . . ] If you have suggestions regarding the content of this guide, send an e-mail with the subject "Service Guide Comments" to channel. services@gateway. com. © 2002 Gateway, Inc. Gateway, Gateway Country, the Gateway stylized logo, and the black-and-white spot design are trademarks or registered trademarks of Gateway, Inc. All other brands and product names are trademarks or registered trademarks of their respective companies. www. gateway. com 1 Replacing Components in Your Gateway SATELLITE C660D Identifying components Where screw measurements are shown, the first number indicates screw head width, and the second number indicates screw length. For a complete list of replaceable parts, see the Contents. LCD panel assembly (see page 33) Keyboard cover (see page 24) Keyboard (see page 26) Palm rest assembly (see page 39) Cooling assembly (see page 44) System board (see page 59) 2 www. gateway. com Preparing your work space Preparing your work space Before performing maintenance on your notebook, make sure that your work space and your notebook are correctly prepared. I I Wear a grounding (ESD) wrist strap, and use a grounded or dissipative work mat. [. . . ] (The screw cannot be removed. ) Screw 18 www. gateway. com Replacing the hard drive kit 4 Lift the screw side of the cover upward, then slide the cover out. 5 Pull on the metal flange to disconnect the hard drive kit from the connector. Flange www. gateway. com 19 Replacing Components in Your Gateway SATELLITE C660D 6 Lift the plastic tab on the hard drive kit, then lift the kit out of your notebook. Tab 7 Place the new hard drive kit into the drive bay, then slide the drive onto the connector. 8 Replace the cover and tighten the screw. 20 www. gateway. com Replacing the hard drive in the hard drive kit Replacing the hard drive in the hard drive kit Tools you need to complete this task: Phillips #0 screwdriver Screws removed during this task: 4 chrome 3 × 3. 5 mm (hard drive) To install a new hard drive into the kit: 1 2 Disconnect the power cord, remove the main and optional secondary battery, and prepare your notebook by following the instructions in "Preparing your work space" on page 3. Remove the hard drive kit by following the instructions in "Replacing the hard drive kit" on page 18. www. gateway. com 21 Replacing Components in Your Gateway SATELLITE C660D 3 Remove the four screws that secure the hard drive to the hard drive kit bracket. Screw Screw Bracket Screw Screw 4 Remove the old drive from the bracket. 22 www. gateway. com Replacing the hard drive in the hard drive kit 5 Insert the new drive into the bracket so the screw holes line up, then replace the four screws that secure the drive to the bracket. Screw Screw Bracket Screw Screw 6 Place the new hard drive kit into the drive bay, then slide the drive onto the connector. 7 Replace the cover and tighten the screw. www. gateway. com 23 Replacing Components in Your Gateway SATELLITE C660D Replacing the keyboard cover Tools you need to complete this task: Flat-blade screwdriver To replace the keyboard cover: 1 2 3 Disconnect the power cord, remove the main and optional secondary battery, and prepare your notebook by following the instructions in "Preparing your work space" on page 3. Be careful not to damage the LCD panel. Tabs 10 11 12 Carefully press the keyboard down until it is flat all the way across. If a grounding strap that was connected to the far-right screw, make sure to reconnect it. Reassemble your notebook. 30 www. gateway. com Replacing the hinge covers Replacing the hinge covers Tools you need to complete this task: Phillips #0 screwdriver Flat-blade screwdriver Screws removed during this task: 4 chrome 2. 5 × 5 mm (hinge covers) To replace the hinge covers: 1 2 3 Disconnect the power cord, remove the main and optional secondary battery, and prepare your notebook by following the instructions in "Preparing your work space" on page 3. Remove the keyboard cover by following the instructions in "Replacing the keyboard cover" on page 24. Open the LCD panel all the way, so it lies flat on the table. www. gateway. com 31 Replacing Components in Your Gateway SATELLITE C660D 4 Remove the four screws that secure the hinge covers to your notebook. Screws Screws 5 Lift the hinge covers off the hinges. 6 7 Snap the new covers into place over the hinges, then replace the four screws. Reassemble your notebook. 32 www. gateway. com Replacing the LCD panel assembly Replacing the LCD panel assembly Tools you need to complete this task: Phillips #0 screwdriver Flat-blade screwdriver Screws removed during this task: 4 chrome 2. 5 × 5 mm (hinge covers) 4 or 6 chrome 2. 5 × 7 mm (LCD panel hinges) To replace the LCD panel assembly: 1 2 3 4 Disconnect the power cord, remove the main and optional secondary battery, and prepare your notebook by following the instructions in "Preparing your work space" on page 3. If your notebook has 802. 11 wireless networking built in, remove the 802. 11 Mini PCI module by following the instructions in "Replacing the 802. 11 Mini PCI card" on page 13. Remove the keyboard cover by following the instructions in "Replacing the keyboard cover" on page 24. Remove the hinge covers by following the instructions in "Replacing the hinge covers" on page 31. www. gateway. com 33 Replacing Components in Your Gateway SATELLITE C660D 5 Use a flat-blade screwdriver or chip puller to carefully unplug the LCD video cable from your notebook. Remove the keyboard cover by following the instructions in "Replacing the keyboard cover" on page 24. Remove the keyboard by following the instructions in "Replacing the keyboard" on page 26. 44 www. gateway. com Replacing the cooling assembly 5 6 7 8 Remove the hinge covers by following the instructions in "Replacing the hinge covers" on page 31. Remove the LCD panel by following the instructions in "Replacing the LCD panel assembly" on page 33. Remove the palm rest assembly by following the instructions in "Replacing the palm rest assembly" on page 39. Unplug the cooling fan. www. gateway. com 45 Replacing Components in Your Gateway SATELLITE C660D 9 Loosen the four captive screws that secure the cooling assembly to your notebook. (These screws cannot be removed. ) Captive screws Captive screws 10 Lift the cooling assembly from your notebook. 46 www. gateway. com Replacing the cooling assembly 11 Insert the new cooling assembly into your notebook, then tighten the four captive screws. Each screw hole has a numeral next to it. Warning When tightening the cooling assembly's chrome screws into the numbered holes, tighten them in numerical order. 12 13 Plug in the cooling fan. Reassemble your notebook. www. gateway. com 47 Replacing Components in Your Gateway SATELLITE C660D Replacing the LED indicator panel Tools you need to complete this task: Phillips #0 screwdriver Flat-blade screwdriver Screws removed during this task: 5 chrome 2. 5 × 4 mm (keyboard) 4 chrome 2. 5 × 5 mm (hinge covers) 4 or 6 chrome 2. 5 × 7 mm (LCD panel hinges) 13 chrome 2. 5 × 5 mm (bottom) 4 chrome 2. 5 × 5 mm (back) 1 chrome 2. 5 × 7 mm (near touchpad) 1 chrome 2. 5 × 4 mm (near multifunction buttons) (palm rest) 1 chrome 2. 5 × 4 mm (LED indicator panel) 48 www. gateway. com Replacing the LED indicator panel To replace the cooling assembly: 1 2 3 4 5 6 7 8 Disconnect the power cord, remove the main and optional secondary battery, and prepare your notebook by following the instructions in "Preparing your work space" on page 3. If your notebook has 802. 11 wireless networking built in, remove the Mini PCI module by following the instructions in "Replacing the 802. 11 Mini PCI card" on page 13. Remove the keyboard cover by following the instructions in "Replacing the keyboard cover" on page 24. Remove the keyboard by following the instructions in "Replacing the keyboard" on page 26. [. . . ] Remove the palm rest assembly by following the instructions in "Replacing the palm rest assembly" on page 39. Remove the eight screws that secure the speakers to your notebook. Screws 52 www. gateway. com Replacing the speakers 9 Move the left speaker out of the way, then unplug the connector for each speaker. 10 Use a flat-blade screwdriver to carefully pry open the metal tabs that secure the wires for the right speaker, then completely remove both speakers. 11 12 Lay the left speaker near the audio board and align the right speaker over its screw holes on your notebook. The left speaker should be attached to the connector furthest from you. www. gateway. com 53 Replacing Components in Your Gateway SATELLITE C660D 13 14 15 Carefully thread the wires for the right speaker under the metal tabs, then press the tabs back down to secure the wires. Reassemble your notebook. 54 www. gateway. com Replacing the audio board Replacing the audio board Tools you need to complete this task: Phillips #0 screwdriver Flat-blade screwdriver Screws removed during this task: 5 chrome 2. 5 × 4 mm (keyboard) 4 chrome 2. 5 × 5 mm (hinge covers) 4 or 6 chrome 2. 5 × 7 mm (LCD panel hinges) 13 chrome 2. 5 × 5 mm (bottom) 4 chrome 2. 5 × 5 mm (back) 1 chrome 2. 5 × 7 mm (near touchpad) 1 chrome 2. 5 × 4 mm (near multifunction buttons) (palm rest) 4 chrome 2. 5 × 4 mm (left speaker) 1 chrome 2. 5 × 4 mm (audio board) www. gateway. com 55 Replacing Components in Your Gateway SATELLITE C660D To replace the audio board: 1 2 3 4 5 6 7 8 Disconnect the power cord, remove the main and optional secondary battery, and prepare your notebook by following the instructions in "Preparing your work space" on page 3. [. . . ]