User manual TOSHIBA SATELLITE 5000-204

[. . . ] These copyrighted materials may be copied for private use at home only. If, beyond the limitation above, you copy (including to transform data formats) or modify these materials, transfer them or distribute them via the Internet without approval of copyright owners, you may be subject to claims for compensation for damage and/or criminal penalties due to infringements of copyrights or personal rights. Please remember to observe the copyright laws when you use this product to copy the copyrighted works or perform other actions. Please note that you may infringe the owner's rights protected by the copyright laws if you use the screen mode switching functions (e. g. [. . . ] Wait for the optical disc indicator to go out before you open the drawer. Also, if the disc is spinning when you open it, wait for it to stop before you remove it. When the drawer pops open slightly, wait a moment to make sure the disc has stopped spinning before pulling the drawer fully open. If the disc is spinning when you open the drawer, it could fly off the spindle and cause injury. The disc extends slightly over the sides of the drawer so you can grasp it. Hold it gently and lift it out. Removing a disc User's Manual 4-22 Operating Basics 3. Press gently until it locks into place. Buttons The Internet button and the CD/DVD button can be assigned functions and applications in the TOSHIBA Controls Properties. After double click this card, the dialog for changing button function is displayed. Choose optimize from left panel then select TOSHIBA Button Controls. TOSHIBA Button Support CD/DVD play control buttons In addition to the power button, the following four buttons control functions relating to the playback of optical media and digital audio data: Play/Pause Stop Next Previous Starts or pauses play Stops play Advances to the next track, chapter or data Returns to the previous track, chapter or data If Random or Shuffle is selected in Windows Media Player, selecting Next or Previous advances to a random selection. User's Manual 4-23 Operating Basics Writing CDs on a CD-RW/DVD-ROM drive You can use the CD-RW/DVD-ROM drive to write data to CD-R/RW discs. The following applications for writing are preinstalled: TOSHIBA Disc Creator/Direct Disc Writer. Important message Before you write or rewrite to CD-R/RW media, read and follow all setup and operating instructions in this section. If you fail to do so, the CD-RW/DVD-ROM drive may not function properly, and you may fail to write or rewrite, lose data or incur other damage. Disclaimer TOSHIBA does not bear responsibility for the following: Damage to any CD-R/-RW disc that may be caused by writing or rewriting with this product. Do not use cutand- paste as the original data will be lost if there is a write error. Writing CDs/DVDs on a DVD Super Multi drive supporting double layer disc recording You can use the DVD Super Multi drive to write data to either CD-R/RW or DVD-R/-RW/+R/+RW/-RAM discs. The following applications for writing are preinstalled: TOSHIBA Disc Creator/Direct Disc Writer. Ulead DVD MovieFactory® for TOSHIBA, which is a product of Ulead Systems, Inc. Important message Before you write or rewrite to CD-R/RW or DVD-R/-RW/+R/+RW/-RAM media, read and follow all set-up and operating instructions in this section. If you fail to do so, the DVD Super Multi drive may not function properly, and you may fail to write or rewrite, lose data or incur other damage. Disclaimer TOSHIBA does not bear responsibility for the following: Damage to any CD-R/RW or DVD-R/-RW/+R/+RW/-RAM disc that may be caused by writing or rewriting with this product. Any change or loss of the recorded contents of CD-R/RW or DVD-R/RW/ +R/+RW /-RAM media that may be caused by writing or rewriting with this product, or for any business profit loss or business interruption that may be caused by the change or loss of the recorded contents. Damage that may be caused by using third party equipment or software. Given the technological limitations of current optical disc writing drives, you may experience unexpected writing or rewriting errors due to disc quality or problems with hardware devices. Also, it is a good idea to make two or more copies of important data, in case of undesired change or loss of the recorded contents. Before writing or rewriting Please observe the following points when you write or rewrite data. Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM media. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates. User's Manual 4-26 Operating Basics CD-R: TAIYOYUDEN CO. , LTD. [. . . ] I/O devices: Equipment used to communicate with the computer and transfer data to and from it. J jumper: A small clip or wire that allows you to change the hardware characteristics by electrically connecting two points of a circuit. K K: Taken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power. KB: See kilobyte. User's Manual Glossary-5 Glossary L Light Emitting Diode (LED): A semiconductor device that emits light when a current is applied. Liquid Crystal Display (LCD): Liquid crystal sealed between two sheets of glass coated with transparent conducting material. The viewing-side coating is etched into character forming segments with leads that extend to the edge of the glass. [. . . ]