User manual TOSHIBA SATELLITE 4070

[. . . ] The warranty contained in the contract between the parties is the sole warranty of Toshiba International Corporation's UPS Division and any statements contained herein do not create new warranties or modify the existing warranty. Any electrical or mechanical modifications to this equipment, without prior written consent of Toshiba International Corporation will void all warranties and may void UL/CUL listing. Unauthorized modifications also can result in personal injury, death, or destruction of the equipment. UNINTERRUPTIBLE POWER SUPPLY If additional information or technical assistance is required beyond what is included in this manual contact Toshiba's marketing department by calling toll free (800) 231-1412, by e-mail at toshibaups@tic. toshiba. com, or write to: Toshiba International Corporation, 13131 W. [. . . ] In order to enter the programming mode the UPS must first be operating in Bypass mode without faults (see "Stopping the UPS: Option 1", page 13). ("Press and hold" always means to hold until the unit gives audible feedback). The unit will give an audible feedback indicating the unit is in programming mode. (If at anytime while the UPS is in the programming mode there is one minute of inactivity the UPS will automatically exit the programming mode and return to bypass operation. ) What follows is a step by step guide to navigating in the programming mode, followed by a detailed description of each option. A. The backup LED will light indicating the UPS is now ready to make changes to the load-shed settings (see "The Load Shed Function", page 16 for an explanation of load shedding). A. 1 The UPS comes from the factory set so the load shed receptacles function for the full battery backup time. The LEDs on the right side of the display will light to indicate the current setting for the load-shed level. For example, since the default factory setting is for no load shed, the first time the option is accessed no LEDs will be lit. This would indicate that the load shed receptacles should be turned off when there is 20% battery power remaining. Pressing the Function Control button successive times will increase the load shed level in 20% increments. A. 2 Once the option is set to the desired level, press and hold the Function Control button. Refer to the section entitled "UPS Connections: Standard Module Connections" on page 10 for an explanation of how to lock and unlock the modules. Figure 5 Expansion Battery Module Other Option Modules There are a number of other optional modules that can be ordered for the SATELLITE 4070 Series UPS system. For information about options not listed here contact Toshiba's UPS Marketing Department at (800) 2311412 or by e-mail at toshibaups@tic. toshiba. com. Description Voltage Voltage UF1-IO-0XX-6BG Dual Transformer Module 208/240V 240/120V Single Isolation 120V 120V UF1-IO-0XX-6AA Transformer Module UF1-IO-0XX-6EE Dual Transformer Module 230V 230V Dual Transformer Module UF1-IO-0XX-XEE 230V 230V with Input Isolation Dual Transformer Module 230V 230V UF1-IO-0XX-EXE with Output Isolation The XX in the part number is replaced by the kVA rating of the system (i. e. 2. 4kVA = 024) Figure 6 shows the standard SATELLITE 4070 series UPS with an optional input isolation transformer module (UF1-IO-024-6AA). Installation of the input transformer requires the input power cord from the electronics module to be plugged into the transformer module. An instruction sheet is included with each module that shows how to connect that particular module. Figure 6 Isolation Transformer Module Communication Interface Dry Contacts The remote contacts interface is a standard feature. It is provided through solid state relays with contacts through a DB9 male connector located on the back of the UPS (refer to the Communication Option User Manual for a more detailed description of this option). Pin 1 2 3 4 5 6 7 8 9 Signal Function Fault Signal UPS stop common UPS stop signal input Normal input power supply Signal common Bypass operation Battery voltage low UPS operation Power failure signal Logic Closed when fault detected Backup stop when the level changes from Low (3 to ­ 15V) to High (+3 ­ +15V) Closed with normal supply power Common signal return Closed during bypass operation Closed at voltage drop Closed during inverter operation Closed at power failure 8 9 In the UPS 1 2 3 4 5 6 7 Voltage 48Vdc peak DB9 Male Connector Outline (facing connector) 30Vac rms (42Vac peak) Current 100mAdc peak 70mAac rms (100mAac peak) RS-232C RS-232C serial communication interface is a standard feature provided through a DB9 female connector located on the backside of the UPS (see "Electronics Module Layout ", page 9). This interface allows communication between the UPS and a personal computer. The chart on the following page shows the signals and the connector pinout. Pin 1 2 3 4 5 6 7 8 9 Signal Name RXD TXD DTR GND DSR RTS CTS - Description In the UPS Receive data Transmit data Data terminal ready Signal ground Data set ready Request to send Clear to send (*) (**) These pins are tied together internal to the UPS. [. . . ] (To start the UPS when the input power is outside of the allowable range see the section entitled "Starting on DC Power", page 13. ) When the UPS is started, if the RUN/STOP switch is in the STOP (bypass) position the unit will start in the on-line mode for 1 second before switching to bypass mode. If the input voltage is out of range the UPS will turn off the output after 1 second rather than switching to bypass. Appendix F: Unit Configuration Options The following chart shows the configuration options for each base model UPS. Model Number Description Available Option Modules Description UF1-BC-087 UF1-IO-015-6BG 48V battery module 208/240V input; 240V/120V output transformer module 120V input isolation transformer module 230V input; 230V output transformer module 230V input isolation, 230V output transformer module 48V battery module 208/240V input; 240V/120V output transformer module 230V input; 230V output transformer module 48V battery module 208/240V input; 240V/120V output transformer module 120V input isolation transformer module 230V input; 230V output transformer module 48V battery module 208/240V input; 240V/120V output transformer module 120V input isolation transformer module 230V input; 230V output transformer module UF1A1A015C6 1500VA Electronics Module UF1-IO-015-6AA UF1-IO-015-6EE UF1-IO-015-XEE UF1A1A015C6T UF1-BC-087 1500VA Electronics UF1-IO-015-6BG Module with internal isolation UF1-IO-015-6EE transformer UF1-BC-087 UF1A1A020C6 2000VA Electronics Module UF1-IO-020-6BG UF1-IO-020-6AA UF1-IO-020-6EE UF1-BC-087 UF1A1A024C6 2400VA Electronics Module UF1-IO-024-6BG UF1-IO-024-6AA UF1-IO-024-6EE \Appendix G: Weights and Dimensions Module Model No. UF1A1A015C6 UF1A1A015C6T UF1A1A020C6 UF1A1A024C6 UF1-BC-087 Module Weight Pounds Kilograms 26 46 30 30 51 12 21 14 14 23 Shipping Weight Pounds Kilograms 31 51 35 35 56 14 23 16 16 25 Electronics Module Dimensions are in inches [mm] Battery/Option Module Dimensions are in inches [mm] TOSHIBA INTERNATIONAL CORPORATION LIMITED WARRANTY POLICY (48 contiguous U. S. States, Canada, Mexico) (UNINTERRUPTIBLE POWER SUPPLIES-UPS) TOSHIBA INTERNATIONAL CORPORATION ("TIC") warrants that the SATELLITE 4070 Series Uninterruptible Power Supplies ("UPS") and Uninterruptible Power Supply Battery ("BATTERY") (external battery cabinet) sold by TIC to the end user ("User") shall be free of defects in material and workmanship. [. . . ]