User manual TOSHIBA RAS-10SKV-E SERVICE MANUAL

[. . . ] SVM-07008-1 SERVICE MANUAL AIR CONDITIONER SPLIT WALL TYPE RAS-10SKV-E / RAS-10SAV-E RAS-10SKV-A / RAS-10SAV-A Revised May, 2007 FILE NO. SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . REFRIGERANT R410A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Hi-POWER OPERATION To automatically control room temperature and airflow for faster cooling or heating operation (except in DRY and FAN ONLY mode) Press HI-POWER : Start and stop the operation. 6. ECO OPERATION To automatically control room to save energy (except in DRY and FAN ONLY mode) Press ECO : Start and stop the operation. Note: Cooling operation; the set temperature will increase automatically 1 degree/ hour for 2 hours (maximum 2 degrees increase). TEMPORARY OPERATION In case of the misplaced or discharged remote control · Pressing the RESET button, the unit can start or stop without using the remote control. · Operation mode is set on AUTOMATIC operation, preset temperature is 24°C and fan operation is automatic speed. TIMER OPERATION Setting the ON Timer Setting the OFF Timer Press Press Press OFF 1 2 3 Press Press Press ON : Set the desired ON timer. : Set the timer. SET SET CLR CLR Everyday timer allows the user to set both the ON & OFF timers and will be activated on a daily basis. Setting Everyday Timer 1 Press ON : Set the ON timer. 3 Press SET . 2 Press OFF : Set the OFF timer. 4 Press button during the ( or ) mark flashing. SET · During the every day timer is activation, both arrows ( or ) are indicated. Note: · Keep the remote control in accessible transmission to the indoor unit; otherwise, the time lag of up to 15 minutes will occur. · The setting will be saved for the next same operation. ­ 44 ­ FILE NO. The setting will be memorized by the unit for future operation (except air flow direction). AUTO RESTART OPERATION To automatically restart the conditioner after the power failure (Power of the unit must be on. ) Setting 1. Press and hold the RESET button on the indoor unit for 3 seconds to set the operation. (3 beep sound and OPERATION lamp blink 5 time/sec for 5 secpmds) · Do not operate ON timer and OFF timer. Press and hold the RESET button on the indoor unit for 3 seconds to cancel the operation. QUIET OPERATION To operate at super low fan speed for quiet operation (except in DRY mode) Press QUIET : Start and stop the operation. Note: Under certain conditions, QUIET operation may not provide adequate cooling or heating due to low sound features. COMFORT SLEEP OPERATION To save energy while sleeping, automatically control air flow and automatically turn OFF. Press COMFORT SLEEP : Select 1, 3, 5 or 9 hrs for OFF timer operation. Note: The cooling operation, the set temperature will increase automatically 1 degree/hour for 2 hours (maximum 2 degrees increase). SLEEP TIMER OPERATION To start the sleep timer (OFF timer) operation Press SLEEP : Select 1, 3, 5 or 9 hrs for OFF timer operation. - 45 - FILE NO. Name and Functions of Indications on Remote Controller [Display] All indications, except for the clock time indicator, are displayed by pressing the 1. Transmission mark This transmission mark indicates when the remote controller transmits signals to the indoor unit. (AUTO : Automatic control, A : Auto changeover : Cool, : Dry, : Heat) control, 3. AUTO or five fan speed levels (LOW , LOW+ , MED , MED+ HIGH ) can be shown. [. . . ] 6) Cut the motor lead at the point which is 100 mm apart from the connector toward the fan. 7) Use the connector used for the inverter, and pinch the lead wires using the closed end splice. 5) Remove the terminal cover of the compressor, and disconnect the lead wire of the compressor thermo and the compressor from the terminal. (ST1T 4 x 10 s 2 PCS. ) Remarks Fan motor Fan motor Propeller fan Closed end splice 10 0 Flange nut , , Compressor Compressor . . . Reactor Reactor ­ 86 ­ FILE NO. [. . . ]