User manual TOSHIBA MT500

[. . . ] OWNER'S MANUAL DATA PROJECTOR TDP-MT500 SAFETY PRECAUTIONS The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Handling the cord on this product or cords associated with accessories sold with this product, will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. [. . . ] At this time POWER indicator blinks in orange. 9 Press POWER ( ) button again. · TELE WIDE 10 Wait about 2 minutes until POWER indicator comes on in orange. · ENTER MENU/EXIT POWER LAMP TEMP POWER button/ POWER indicator · · POWER ON/OFF POWER button C1 COMP1 · SOURCE C2 COMP2 DVI D DVI-D Wait about 2 minutes in standby state, because during this time the intake/exhaust fan is turning to cool down the light-source lamp. The intake/exhaust fan continues to turn for about one minute after POWER indicator has come on in orange. Do not turn off the main power switch while POWER indicator is blinking. If the main power switch is turned off immediately after use, the projector may fall in failure. The fan generates a loud sound while cooling down, but it is not a failure. S S-VIDEO V VIDEO DVI A DVI-A 16:9 16:9 4:3 4:3 ZM ZOOM REAL REAL ASPECT DYN DYNAMIC 2 1 3 11 Turn "OFF" the main power switch (Turn to indication O). · · When the projector is not used for a long time, unplug the power plug from the power outlet for safety. Set the lens cap to prevent dust from being gathered from outside. ENTER MENU EXIT CNT BRI COL COLOR TIN TINT CONTRAST BRIGHT TEM COLOR TEMP GAM SH GAMMA SHARPNESS LIGHT LIGHT Note-book type computer When the projector is connected to a note-book type computer, the picture images from the computer may not be projected on screen. On this occasion, setup the computer so that it may output picture signals. Example of setup for the external output: Press "Fn" key and any of "F1" to "F12" key (Depends on the type of the computer). 26 SETTING WITH MENUS Menu construction PICTURE. . . CONTRAST BRIGHTNESS COLOR TINT SHARPNESS ­ 32 ~ +31 ­ 30 ~ +30 ­ 30 ~ +30 ­ 15 ~ +15 ­ 10 ~ +10 ICC RED ICC GREEN ICC BLUE ICC YELLOW ­ 15 ~ +15 ­ 15 ~ +15 ­ 15 ~ +15 ­ 15 ~ +15 9300 / 6500 / 5700 / USER1 / USER2 LOAD FROM R GAIN G GAIN B GAIN R BIAS G BIAS B BIAS SAVE TO 9300 / 6500 / 5700 / USER1 / USER2 1 - 512 1 - 512 1 - 512 0 - 90 0 - 90 0 - 90 USER1 / USER2 CINEMA1/CINEMA2/VIDEO1/VIDEO2/STANDARD VIDEO/S-VIDEO/COMPONENT1/COMPONENT2/ DVI-DIGITAL/DVI-ANALOG 16:9 / 4:3 / ZOOM / DYNAMIC / REAL MEMORY1 / MEMORY2 / MEMORY3 YES / NO 0 / 10 / 20 / 30 / 40 / 50 / 60 / 70 / 80 / 90 MINUTES PRO-PICTURE. . . ICC CONTROL COLOR TEMP SET USER COLOR TEMP GAMMA DISPLAY. . . PATTERN / ENGLISH / YES ­ 15 ~ +15 0 ~ 31 ­ 30 ~ +30 ­ 30 ~ +30 / / FLOOR FRONT / CEILING FRONT / FLOOR REAR / CEILING REAR ­ 12 ~ +12 · The items with mark " " or ". . . " requires to press ENTER button to confirm its entry after selecting the item. 27 SETTING WITH MENUS How to make menu setting: The following figures describe how to set trapezoidal correction as an example: 1 Press MENU button. INSTALLATION. . . 6 Press $ , % buttons for the setting. INSTALLATION. . . KEYSTONE KEYSTONE +4 2 Select the menu to be revealed by pressing { , } buttons. PICTURE. . . · When EXIT button of the remote controller is pressed, the display returns to the menu of the previous level. 3 Press ENTER button. LANGUAGE RGB & COMPONENT MIRROR KEYSTONE PATTERN 4 Select the menu to be revealed by pressing { , } buttons. INTTALLATION. . . LANGUAGE RGB & COMPONENT MIRROR KEYSTONE PATTERN 5 Press ENTER button. KEYSTONE KEYSTONE 0 28 SETTING WITH MENUS Items that can be set with menus In this projector, the following items can be set by revealing setup menus. CONTRAST BRIGHTNESS COLOR TINT SHARPNESS 0 0 0 0 0 ITEM SETTING FUNCTION CONTRAST ------- -32 ­ +31 ---------- Adjusts contrast of projected images. (See Page 28. ) BRIGHTNESS ---- -30 ­ +30 ---------- Adjusts brightness of projected images. (See Page 28. ) COLOR ------------- -30 ­ +30 ---------- Adjusts color thickness of projected images. (See Page 28. ) TINT --------------- -15 ­ +15 ---------- Adjusts tint of projected images. (See Page 28. ) SHARPNESS ----- -10 ­ +10 ---------- Adjusts sharpness of projected images. (See Page 28. ) ITEM SETTING FUNCTION ICC CONTROL ---------------------------- Emphasizes or de-emphasizes independently each of four colors, RED, GREEN, BLUE and YELLOW. COLOR TEMP ----------------------------- Selects one of preset color temperatures. [. . . ] Purchase a light-source lamp from the delivery agent of the projector. On in red Kensington Lock This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System. Refer to the information that came with the Kensington System for instructions on how to use it to secure the projector. Kensington Technology Group 2855 Campus Drive San Mateo, CA 94403, U. S. A. Phone : (650)572-2700 Fax : (650)572-9675 38 WHEN ASKING INSTALLATION WORK In the case of suspending the projector from ceiling and viewing the projected images from the front side: When suspending the projector from ceiling, use the separately sold dedicated metal bracket (see Page 38). [. . . ]