User manual TOSHIBA MAGNIA Z300

[. . . ] Note: Before removing any PC Card device, make sure it is "STOPPED" in the PC Card manager. MEMORY MEMORY REMOVAL Memory cover M2x2. 5 black screws 1. Remove two M2x2. 5 black screws securing the memory cover. Memory module M2x3 black flat head screw 3. Disconnect the memory module from the top side as shown by the arrow above. Tough Enough for Today's World. TOSHIBA FIELD REPLACEABLE UNIT DOCUMENTATION Portege P2000 Series HDD REMOVAL TM HDD cover M2x4 black screws 1. [. . . ] Remove two M2x4 black screws securing the HDD cover and lift it out. HDD connector HDD assembly 3. CAUTION: Be very careful not to press on the TOP or BOTTOM of the HDD. Pressure can destroy data or damage the drive. HDD REMOVAL HDD pad KEYBOARD REMOVAL HDD rubber holder M2x3 black flat head screw 1. Remove the HDD rubber holder and the HDD pad. Tough Enough for Today's World. TOSHIBA FIELD REPLACEABLE UNIT DOCUMENTATION Portege P2000 Series KEYBOARD REMOVAL Latch TM Keyboard holder M2x3 silver flat head screws 3. Remove two M2x3 silver flat head screws securing the keyboard. KEYBOARD REMOVAL TOP COVER REMOVAL M2. 5x6 black flat head screws PJ445 M2x6 black screws Keyboard Keyboard cable 5. Remove the rubber cover close to the HDD slot and remove one M2x4 brass screw. Remove the following screws from the bottom cover: - 9 M2x6 black screws - 2 M2. 5x6 black flat head screws - 2 M2x4 black screws and 1 M2x4 brass screw Tough Enough for Today's World. TOSHIBA FIELD REPLACEABLE UNIT DOCUMENTATION Portege P2000 Series TOP COVER REMOVAL Power button/ LED board cable PJ7 Top cover TM Internet/In Touch buttons cable PJ8 Flexible PWB PJ334 PJ9 Touch Pad cable 3. Disconnect the following cables by carefully lifting the lever using from the PCB: - Touch Pad cable from PJ334 - Flexible PWB from PJ9 - Internet/ In-Touch Buttons cable from PJ8 - Power Button/ LED board cable from PJ7 M2x4 brass screws 5. Remove two cool sheets on the top side of the system board. Tough Enough for Today's World. TOSHIBA FIELD REPLACEABLE UNIT DOCUMENTATION Portege P2000 Series TOUCH PAD REMOVAL Touch pad board Touc pad/ Membrane cable copper tape TM RTC/ Speaker holder M2x4 brass screws 1. Remove one M2x4brass screw securing the LCD latch assembly and lift it out. Disconnect the Touch pad/ Membrane cable from the touch pad board. LCD latch assy Touch pad bracket M2x3 silver flat head screws 1. Remove four M2x3 silver flat head screws securing the Touch pad assembly. Separate the touch pad board from the touch pad bracket. Tough Enough for Today's World. TOSHIBA FIELD REPLACEABLE UNIT DOCUMENTATION Portege P2000 Series DISPLAY MASK REMOVAL LCD cushions TM FL INVERTER AND LCD REMOVAL FL inverter cable LCD module M2x3 silver Flat head screw Display mask FL inverter board LCD mask seals 1. Remove one LCD cushions and six LCD mask seals using a pair of fine-tipped tweezers. Remove one M2x3 black flat head screw and six M2x3 silver flat head screws securing the display mask. Lift out the display mask. LCD cable LCD module FL cable 1. [. . . ] Remove one M2x3 black flat head screw and six M2x3 silver flat head screws securing the display mask. Lift out the display mask. LCD cable LCD module FL cable 1. Remove one M2x3 silver flat head screw securing the FL inverter board. [. . . ]