User manual TOSHIBA M250

[. . . ] ·This AC mains adapter should only be connected to an AC 230V/50Hz mains power supply - do not attempt to connect it to any other type of supply. ·The socket-outlet must be installed near the equipment and easily accessible. ·Always hold the plug when pulling it out from the power mains supply system. ·This unit is recommended to be installed on shock-free benches in order to avoid any danger from falling. [. . . ] [RED] button. View information for future programmes on the current channel. . . Change the Subtitle setting (if available). . . [GREEn] button. [YELLoW] button. [oK] button. [ ] button (whilst viewing that programme's information). Refer to page 22 for more information. Switch to another channel (when viewing that channel's information). . . Set a current or future programme to record. . . Exit Info. . . [InFo] or [BACK] button. 20 M250 User Guide. indb 20 22/07/2010 10:38 Picture In Picture (PIP) Picture In Picture allows you to watch two channels at the same time. The sound from the main picture is always played. PIP screen (highlighted) Using your Digital TV recorder To Switch on Picture In Picture. . . Move the PIP screen. . . Press Change the channel displayed in the PIP screen. . . [PIP] button. [PIP] button. [ / / / ] buttons. Change the channel displayed in the main picture. . . Exit Picture In Picture. . . [Ch+/-] buttons, when the PIP screen is selected. [0]-[9] buttons. The [Ch+/-] buttons can also be used when the PIP screen is not selected. [ ] button. [PIP] button, when the PIP screen is selected/highlighted. note: · Picture In Picture is not available when recording programmes. 21 M250 User Guide. indb 21 22/07/2010 10:38 Using your Digital TV recorder Recording Programmes This Digital TV recorder has twin tuners, making it possible to record two programmes at the same time. If none of the programmes are repeated, simply delete one of the planned recordings by pressing the [RED] button (Delete). note: · · · The Digital TV recorder will record programmes even if the programme is shown later than advertised e. g. It is safe to put the Digital TV recorder into Standby when you have set programmes to record. The Digital TV recorder will automatically wake up from Standby to make the recording. The Digital TV recorder will also automatically add 3 minutes to the end of each recording to make sure the entire programme is recorded. However, if any subsequent recording starts during those 3 minutes, then the firstrecordingwillbestoppedtoallowthenewrecordingtocommence. 24 M250 User Guide. indb 24 22/07/2010 10:38 Timeshifting Timeshifting allows you to Pause live TV, it lets you pause a broadcast programme and continue watching it later. The maximum length of time you can pause a programme for is 4 hours. Using your Digital TV recorder Timeshift banner Pausing Live TV ·Press to pause live TV. Press to resume. note: · When live TV is paused, the timeshifting banner is displayed indicating how long the programme has been paused. · The length of time you can pause a programme can be adjusted in the menu. See `Pause Buffer Size' on page 35. Rewinding Live and Timeshifted TV ·Press to rewind live TV. Press note: · You can press to resume. a further 3 times to rewind faster. Fast Forwarding Timeshifted TV ·Press note: · You can press to fast forward timeshifted TV. Press a further 3 times to fast forward faster. to resume. ·Press ·Press ·Press Watching in Slow Motion to pause live TV or a recording. [. . . ] Continuously press the [Ch+] or [Ch­] button until the TV set switches off, then press the [oK] button to save the codeset and the [ TV] button illumination goes off. If they don't, go back to steps (2) and (3). Finding the Remote Control's Current Codes If you have used the procedure above to programme the remote control to operate your TV, it may be useful to know the correct code for your TV. note: · Knowing the codes that operate your equipment will allow you to re-programme the remote control using the procedure on the previous page, should the need arise. Make a note of your code and keep it in a safe place. Additional Information 1. Press and Hold the [ ] button and [GUIDE] button at the same time for 3 seconds, then the [ TV]buttonflashestwiceandswitchesOFF. [. . . ]