User manual TOSHIBA IK-HR2D

[. . . ] CMOS COLOR CAMERA INSTRUCTION MANUAL IK-HR2D For Customer Use Enter the Serial # (which is located on the bottom of the cabinet) below. Model # Serial # IK-HR2D FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. [. . . ] TEMP LOW Meaning Automatic white balance adjustment finished correctly. Automatic white balance adjustment cannot be performed because the video level is too low. Adjust the video level by increasing the illumination or opening the lens iris. Automatic white balance adjustment cannot be performed because the video level is too high. Adjust the video level by decreasing the illumination or closing the lens iris. Automatic white balance adjustment cannot be performed because the color temperature is too low. If the message appears with the C. TEMP set to 3200K, change the illumination or use a color temperature conversion filter. AWB NG C. TEMP HIGH Automatic white balance adjustment cannot be performed because the color temperature is too high. If the message appears with the C. TEMP set to 5600K, change the illumination or use the color temperature conversion filter. AWB NG Automatic white balance adjustment cannot be performed for other reasons. Such as no white area is included in an object, etc. (2) MANUAL(Manual white balance) Set the MODE to MANUAL on the WHT BAL menu. (Refer to the item "7. 3 (3) WHT BAL (White Balance)". ) Shoot a known white object, set the white balance by adjusting the levels of R GAIN and B GAIN on the menu, confirming with a monitor or a vector scope. (Refer to the item "7. 3 (3) (3. 3) Changing gain in MANUAL mode". ) 11 5 2 Gain When the image is dark even if the lens iris is open, change the gain (video gain) to get the desired video level. For gain adjustment of the unit, MANUAL (Manual), OFF (0 dB) modes are provided. (Refer to the item "7. 3 (2) GAIN (Video gain)". ) (1) MANUAL(Manual gain) Gain adjustment is performed on the GAIN menu. (Refer to the item "7. 3 (2) (2. 1) Changing gain in MANUAL mode". ) (2) OFF Gain is fixed at 0 dB. Note: White, red, green, or blue dots may occur when the gain is increased. This is not a malfunction, just certain characteristics of the CMOS sensor becoming more visible. 5 3 Switching video signal output By turning on the power while the control buttons on the rear panel are pressed, the video signal output of the DVI-D terminal can be switched. When the video signal output is switched, a mode is displayed on the screen for about 5 seconds. "1080p 59. 94" Mode 1080/59. 94p 1080/50p 1080/59. 94i 1080/50i 720/59. 94p 720/50p Resolution 1920×1080/59. 94Hz (progressive) 1920×1080/50Hz (progressive) 1920×1080/59. 94Hz (interlace) 1920×1080/50Hz (interlace) 1280×720/59. 94Hz (progressive) 1280×720/50Hz (progressive) How to operate Turn on power while pressing [DISP] Turn on power while pressing [PAGE] Turn on power while pressing [MENU UP] Turn on power while pressing [MENU DOWN] Turn on power while pressing [DATA UP] Turn on power while pressing [DATA DOWN] Note: Resolution specified by the computer to which a USB cable is connected has priority while displaying/recording video from the USB terminal. Please disconnect the USB cable before switching the video signal output. 12 5 4 Display video with USB Connect a USB terminal of the camera and a USB terminal of the computer with a USB cable. * Please use a cable supporting mini-USB (B type) for the USB terminal of the camera. * To display video captured by the camera, viewer software supporting USB Video Class is required separately. * In case of Windows® XP SP2 or SP3, the built-in viewer software can be used. [. . . ] Before seeking warranty service, you should check the troubleshooting guide in the Instruction Manual (Owner's Manual) and follow the instructions to correct the problem. Your Responsibilities This Limited Warranty is subject to the following conditions: 1. You must provide the bill of sale or proof of purchase at the time that warranty service is required. You must notify an ASP within thirty (30) days after You discover that the Product does not perform in accordance with specifications during the Limited Warranty period. [. . . ]