User manual TOSHIBA IK-TF5C

[. . . ] INSTRUCTION MANUAL 3 CCD CAMERA IK-TF5C For Customer Use Enter below the Serial No. Model No. : IK-TF5C Serial No. : FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. [. . . ] 2 Select either OFF/120fps/180fps/E. 120fps/E. 180fps by pushing [DATA UP], [DATA DOWN] buttons. 12 (1. scan) mode Move up down By pushing MENU UP, DOWN Set by pushing DATA UP, DOWN · Sutter mode MANU, SS, E. TRG -- SHUTTER -MODE SS PART SS OFF OFF · Synchro. scanning setting OFF : 1H/525H524H/525HOFF2FRM512FRM 120fps, E. 120fps : 1H/262H261H/262HOFF2FRM512FRM 180fps, E. 180fps : 1H/175H174H/175HOFF2FRM512FRM · Partial scanning switch OFF/120fps/180fps/E. 120fps/E. 180fps <MODE = SS> (a) Changing the shutter speed setting 1 Set the "" to SS by pushing [MENU UP], [MENU DOWN] buttons. 2 Select the shutter speed by pushing [DATA UP], [DATA DOWN] buttons. (b) Partial scanning setting 1 Set the "" to PART by pushing [MENU UP], [MENU DOWN] buttons. 2 Select either OFF/120fps/180fps/E. 120fps/E. 180fps by pushing [DATA UP], [DATA DOWN] buttons. Note: The slow shutter speed may increase the fixed pattern noise and/or the white pixels. This is a characteristic of CCD, and is not a symptom of malfunction. 13 (1. 3) Changing each setting in E. TRG mode The E. TRG has five modes; 1P SNR, 1P SR, PW SNR, PW SR, RR. TRG, then set the "" to E. TRG and select the desired E. TRG mode. (1. 1) Changing each setting in 1P SNR mode Move up down By pushing MENU UP, DOWN Set by pushing DATA UP, DOWN -- SHUTTER -MODE E. TRG TRG. P EXP. PART E. TRG 1P SNR 16ms OFF · Sutter mode MANU, SS, E. TRG · E. TRG mode 1P SNR, 1P SR, PW SNR, PW SR, RR · Input trigger pulse setting at 1P SNR and 1P SR Input trigger pulse : positive polarity Input trigger pulse : negative polarity · Exposure time setting at 1P SNR and 1P SR 0. 01 ms 0. 02 ms 0. 4 ms 1 ms 16 ms 0. 01 ms 0. 02 ms 0. 1 ms 1 ms step step step step · Partial scanning switch OFF/120fps/180fps/E. 120fps/E. 180fps <MODE = E. TRG E. TRG = 1P SNR> (a) Changing the polarity of inputting trigger pulse setting 1 Set the "" to TRG. P by pushing [MENU UP], [MENU DOWN] buttons. 2 Select either (b) Changing 1P SNR exposure time setting 1 Set the "" to EXP. Note: The longer the storage time with extended exposures, the more visible certain characteristics of CCD cameras become: fixed pattern noise, white pixels, etc. (c) Changing the partial scanning setting 1 Set the "" to PART by pushing [MENU UP], [MENU DOWN] buttons. 2 Select either OFF/120fps/180fps/E. 120fps/E. 180fps by pushing [DATA UP], [DATA DOWN] buttons. 14 (1. 2) Changing each setting in 1P SR mode Move up down By pushing MENU UP, DOWN Set by pushing DATA UP, DOWN -- SHUTTER -MODE E. TRG TRG. P EXP. PART E. TRG 1P SR 16ms OFF · Sutter mode MANU, SS, E. TRG · E. TRG mode 1P SNR, 1P SR, PW SNR, PW SR, RR · Input trigger pulse setting at 1P SNR and 1P SR Input trigger pulse : positive polarity Input trigger pulse : negative polarity · Exposure time setting at 1P SNR and 1P SR 0. 01 ms 0. 02 ms 0. 4 ms 1 ms 16 ms 0. 01 ms 0. 02 ms 0. 1 ms 1 ms step step step step · Partial scanning switch OFF/120fps/180fps/E. 120fps/E. 180fps <MODE = E. TRG E. TRG = 1P SR> (a) Changing the polarity of inputting trigger pulse setting 1 Set the "" to TRG. P by pushing [MENU UP], [MENU DOWN] buttons. 2 Select either (b) Changing 1P SR exposure time setting 1 Set the "" to EXP. Note: The longer the storage time with extended exposures, the more visible certain characteristics of CCD cameras become: fixed pattern noise, white pixels, etc. (c) Changing the partial scanning setting 1 Set the "" to PART by pushing [MENU UP], [MENU DOWN] buttons. 2 Select either OFF/120fps/180fps/E. 120fps/E. 180fps by pushing [DATA UP], [DATA DOWN] buttons. 15 (1. 3) Changing each setting in PW SNR mode Move up down By pushing MENU UP, DOWN Set by pushing DATA UP, DOWN · Sutter mode MANU, SS, E. TRG -- SHUTTER -MODE E. TRG TRG. P PART E. TRG PW SNR OFF · E. TRG mode 1P SNR, 1P SR, PW SNR, PW SR, RR · Input trigger pulse setting at PW SNR and PW SR Input trigger pulse : positive polarity Input trigger pulse : negative polarity · Partial scanning switch OFF/120fps/180fps/E. 120fps/E. 180fps <MODE = E. TRG E. TRG = PW SNR> (a) Changing the polarity of inputting trigger pulse setting 1 Set the "" to TRG. P by pushing [MENU UP], [MENU DOWN] buttons. 2 Select either (b) Changing the partial scanning setting 1 Set the "" to PART by pushing [MENU UP], [MENU DOWN] buttons. 2 Select either OFF/120fps/180fps/E. 120fps/E. 180fps by pushing [DATA UP], [DATA DOWN] buttons. [. . . ] The user must deliver the entire product to an ISD authorized service center. The user is responsible for all transportation and insurance charges for the product to the Service Center. ISD reserves the right to substitute Factory Refurbished Parts and / or Factory Refurbished Product in place of those in need of repair. Step-by-step Procedures - How to Obtain Warranty Service [1] Verify operation of the unit by checking the instruction manual [2] If there is a defect in material or workmanship, contact an Authorized Service Provider within 30 days after the product fails to comply with specifications. [. . . ]