User manual TOSHIBA FT8001AW

[. . . ] IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Do not use this product near water sources, such as bath tubs, wash bowls, kitchen sinks, laundry tubs, wet basements, or swimming pools. Slots and openings in the cabinet and the back or bottom are provided for ventilation, to protect the phone from overheating. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. [. . . ] SETTING UP THE BASE UNIT For use on a desk or counter top follow the instructions below. DESKTOP MOUNTING: Fasten the AC adaptor cord to prevent it from being disconnected. Raise the antenna to vertical position. Single-Line Telephone Jack (RJ11C) Telephone Line Cord Power Outlet (AC 120V, 60Hz) AC Adaptor · USE ONLY WITH Supplied AC ADAPTOR (TAC-8001); power source AC 120V, 60Hz/DC 9V). CHARGE THE BATTERY PACK Note Red Black Use only the supplied battery pack (TRB-8000 power source 600 mAh, 3. 6V). q Remove the battery compartment cover on the back of the handset by sliding it down. w Plug the battery pack cord into the connector in the battery compartment by observing the correct polarity. r Put the battery compartment cover back by sliding until it snaps into place. Make sure not to get the wires of the battery pack caught in the cover. If the IN USE/CHARGE LED does not light, make sure the AC adaptor is plugged in securely and that the electrical outlet is working and not controlled by a light switch. It is important to charge the battery for 12 to 16 hours continuously without any interruption before you use the handset for the first time. 90 0M Hz Charging contacts IN USE/ CHARGE LED Note The battery pack is not charged properly if the charging contacts are dirty or tarnished. Clean the contacts occasionally with a dry cloth. 6 After the battery pack is fully charged; Operation While in use (Talk mode) While not in use (Standby mode) Approx. battery life up to 7 hours up to 14 days When TALK/BATT LOW LED blinks, all handset buttons are disabled and the battery needs to be charged. Finish the call as soon as possible and place the handset on the base unit. Note If a call comes in when the battery is too low to operate properly, you will be unable to answer the call or the call will be disconnected. WALL MOUNTING MOUNTING ON A STANDARD WALL PLATE Insert the bracket's tab into the base's lower tab slots, then press down on the top of the bracket to snap it into the clip slots. Raise the antenna. Flip the switch hook tab over so the tab holds the handset. Telephone Line Cord Single-Line Telephone Jack (RJ11C) Power Outlet (AC 120V, 60Hz) AC Adaptor 7 · Route the cords through the guides. · Place the base unit on the posts of the wall plate and push down until it is firmly seated. · USE ONLY WITH Supplied AC ADAPTOR (TAC-8001 power source AC 120V, 60Hz/DC 9V). Notes · Do not use any outlet controlled by a wall switch. · If you don't have a standard wall plate, cut out the template on this page and use it to position two screws (minimum length of 13/8 inches) into the wall with the heads protruding about 1/4 inch. CUT CUT Wall mount template IMPORTANT: · Before mounting, select a wall area of sufficient strength. If mounting on wallboard or in an area of questionable strength, locate a stud for maximum support of your telephone. The TALK/BATT LOW LED will light. 1, 2 w To hang up, press TALK or place the handset on the base unit. INTERFERENCE OR STATIC If you hear noise during a call, press CH to select another channel. CHANGING THE RINGER VOLUME Press VOL/RING to select one of four ringer tone and volume combinations during standby mode. CHANGING THE HANDSET SPEAKER VOLUME During a telephone call, press VOL/RING to select one of three speaker volume levels; Low, Medium and High. [. . . ] SOLUTION · The charging contacts of the handset and base are not clean. · The battery connector is not connected with correct polarity. · Outlet used is controlled by a wall switch in its OFF position. Recharge the battery. Battery becomes low quickly. Can not make or receive calls. [. . . ]