User manual TOSHIBA DVR-18-DTKB

[. . . ] E9NG1BD_EN. book Page 1 Monday, April 7, 2008 5:54 PM Introduction Connections DVD VIDEO RECORDER / VIDEO CASSETTE RECORDER Basic Setup D-VR18DTKB OWNER'S MANUAL PAL Recording Playback Editing Function Setup PAL DVD -RW/R +RW/R RECORDING DVD/VIDEO CASSETTE RECORDER D-VR18DT ON/STANDBY REC PROGRAM DUBBING VCR/DVD REC VCR Functions VCR VCR DVD DVD Others © 2008 Toshiba Corporation E9NG1BD_EN. book Page 2 Monday, April 7, 2008 5:54 PM Introduction Precautions WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The important note is located on the rear of the cabinet. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Laser Safety This unit employs a laser. Only a qualified service personnel should remove the cover or attempt to service this unit, due to the possibility of eye injury. [. . . ] (See "Video Colour System" on page 47 for details. ) · If the external equipment is connected to AV2, the picture of the external equipment will be output except during the DVD playback of this unit. Turn off the external equipment or press [DISPLAY] to output the picture of this unit. · If you wish to make a recording from the DV input (AV4) on the front panel, see instructions for this starting on the following. DV AB-1234 0:12:34 5 SP 2:00 7 6 The menu changes according to the mode of DVC. Switch the mode on the DVC to video mode for the dubbing information. 48 EN E9NG1BD_EN. book Page 49 Monday, April 7, 2008 5:54 PM Introduction The following instructions are described with the operations using the remote control of this unit. DVC to DVD Dubbing Video VR 1 2 DV icon Indicator of active device · With "Control" highlighted, press [ENTER / OK] to display the available devices to control with the remote control of this unit. Select the device you want to operate using [U / D], then press [ENTER / OK]. - Select "DVD" to control this unit with the remote control of this unit. - Select "DVC" to control your DVC with the remote control of this unit. DVD-RW DVD-RW DVD-R DVD+RW DVD+RW VD+RW DVD+R DVD+R Before recording from DVC, see pages 21 to 22 for connection instructions. (See page 86 for DVC to VCR dubbing. ) Connections Preparing for DV dubbing (DVC to DVD): · Insert a recordable DVD. If you are copying to a disc, press [DVD] first. 3 Recording audio mode · "DV Audio" can be changed. With "DV Audio" selected, press [ENTER / OK] to display "DV Audio" menu. Select the audio you want to output using [U / D], then press [ENTER / OK]. - Select "Stereo2" to copy the sound that was added after the recording. - Select "Mix" to copy the stereo1 and stereo2. Basic Setup 1 Select "DV" channel using [INPUT SELECT ] or [PROG. / ]. 4 5 6 Command menu · "Start Rec" or "Pause Rec" will appear. DV AB-1234 0:00:00 Recording External input channel Product name of your DVC · If the unit cannot recognise the input signal from the DVC or if it is the unknown product, "No Device" or "****" will appear instead. 2 3 4 Press [REC MODE] to select a recording mode. With "Control" highlighted, press [ENTER / OK] to display the available devices to control with the remote control of this unit. Select "DVC" using [U / D], then press [ENTER / OK]. e. g. ) DVC to DVD dubbing T 1/ 1 C 1/ 1 -RW Control DV Audio Start Rec DVD Stereo 1 VR ORG 7 Status of the current operation and the time counter Each icon means (Available icons may vary depending on the DVC): DVC is in stop mode. DVC is in recording pause mode. Playback Editing DV AB-1234 0:00:00 Function Setup SP 2:00 Now you can operate your DVC with the remote control of this unit. VCR Functions 5 Press [PLAY B] to start playing back the DVC, and find where you want to start dubbing. Select "Start Rec" using [U / D], then press [ENTER / OK]. The dubbing will start. 6 Others Please also read the operating instructions of your DVC for more information. EN 49 E9NG1BD_EN. book Page 50 Monday, April 7, 2008 5:54 PM To stop dubbing; 1 2 3 Select "Control" using [U / D], then press [ENTER / OK]. Press [STOP C]. Dubbing Mode Video VR DVD-RW DVD-RW DVD-R DVD+RW DVD+RW VD+RW Note · The tape will rewind a few seconds when you press [ENTER / OK] at step 6 so that the dubbing starts exactly where you press [PAUSE F] instead of [STOP C] at step 5. Other DV device such as cable/satellite box or D-VHS VCR cannot be recognised. · If no video signal is detected from the DVC during DVC to DVD dubbing, the recording will be paused and "I" will flash on the TV screen. The recording will resume when the unit detects the video signal again. [. . . ] Once [INSTANT SKIP] is pressed, the start point will be set forward 30 seconds and playback resume automatically. (You can press [INSTANT SKIP] up to 6 times. ) JPEG (Joint Photographic Experts Group) JPEG is a method of compressing still image files. You can copy JPEG files on CD-RW/-R discs from a computer and play back the files on this unit. You can copy MP3 files on CD-RW/-R discs from a computer and play back the files on this unit. [. . . ]