User manual TOSHIBA D-VR16

[. . . ] Introduction Connections Basic Setup Recording Playback Editing Function Setup VCR Functions Others DVD VIDEO RECORDER / VIDEO CASSETTE RECORDER REC DVD VCR/DVD D-VR16SB PROGRAM REC DUBBING VCR ON / STANDBY ® VCR DVD DVD VIDEO RECORDER / VIDEO CASSETTE RECORDER D-VR16SB 1VMN22711 / E9BA1BD 2006 Introduction Precautions WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The important note is located on the rear of the cabinet. Laser Safety This unit employs a laser. [. . . ] · After connecting to a Dolby Digital decoder, set "Dolby Digital" to "Stream" in the Audio menu. (See page 121. ) · After connecting to a DTS decoder, set "DTS" to "ON" in the Audio menu. (See page 121. ) · After connecting to a MPEG decoder, set "MPEG" to "Stream" in the Audio menu. (See page 121. ) Connecting to an MD deck or DAT deck · The audio source recorded in Dolby Digital multi- channel surround format cannot be recorded using an MD or DAT deck as a digital sound. · If not connected to a Dolby Digital decoder, set "Dolby Digital" to "PCM" in the Audio menu (see page 121). · Playing back a DVD using incorrect settings may generate noise distortion, and damage speakers. · Set "Dolby Digital" and "MPEG" to "PCM" and set "DTS" to "OFF" in the Audio menu (see page 121) for connecting to an MD or DAT deck. · You can use AUDIO OUT jacks for the connection of your audio system. 28 EN Basic Setup Read this chapter for necessary settings to get started. Initial setting Channel setting Setting the clock Selecting the TV aspect ratio Basic Setup Initial setting You need to follow these steps when you turn this unit on for the first time. 4) After channel setting is finished, "Clock Setting" will appear. Then press [ENTER]. Initial Setting Clock Setting 1) Press [I/y ON/STANDBY]. Select the input to which the unit is connected. Initial Setting menu will automatically appear. 3) Press [ENTER] to start Channel Tuning. Initial Setting Channel Tuning Clock Setting menu will appear. 5) Press [ENTER] again, then follow the steps 4 to 5 on page 34 in "Manual Clock Setting". The unit will start getting channels available in your area. 30 EN Basic Setup Introduction Channel setting Tuning of this unit to broadcast channels can be performed in two ways. Auto tuning Programme the tuner to scan only the channels you can receive in your area. 4) Press [SETUP] to exit. You can select only the channels memorised in this unit by using [PROG. / ], or directly enter the channel using [the Number buttons] on the remote control. Notes · The selection will be affected by how you receive TV channels in your local area. · If the auto tuning is cancelled during scanning, some channels not yet tuned may not be received. · Sorting of TV channels from P01 to P06 will be performed automatically as follows. P01: BBC1 P02: BBC2 P03: ITV P04: CH4 P05: CH5 P06: SKY NEWS * If you are using a satellite receiver, turn it on and select SKY NEWS before commencing tuning. Connections 1) In stop mode, press [SETUP]. Setup Required Setting Playback Display Recording Clock Channel Disc Basic Setup Recording Setup menu will appear. 2) Select "Channel" using [K / L], then press [ENTER]. Setup Required Setting Playback Display Recording Clock Channel Disc Manual tuning Manually tune each channel. Playback 1) In stop mode, press [SETUP]. Editing 3) Select "Manual Tuning" using [K / L], then press [ENTER]. Manual Tuning Channel menu will appear. 3) Select "Auto Tuning" using [K / L], then press [ENTER]. The unit will start storing channels available in your area. Channel Auto Tuning Manual Tuning Move VCR DVD Function Setup Position Channel Decoder Skip P01 1 OFF ON VCR DVD VCR Functions 4) Select "Position" using [K / L], then press [B]. 5) Select the position number you want using [K / L], then press [s]. Wait for several minutes to finish channel storing. You can select position numbers 01 to 99. 6) Select "Channel" using [K / L], then press [ENTER]. Others EN 31 Basic Setup Channel setting (cont'd) 7) Press [K / L] to start scanning. · The tuner will begin to search up or down automatically. When a channel is found, the unit will stop searching and the picture will appear on the TV screen. · You can select a desired channel number using [the Number buttons]. Refer to the following Channel Plan table and press the three digits to select the channel number. Or press [4] and then "­ ­ 4" appears and wait for 2 seconds. ) · If this is the channel you want, press [s]. [. . . ] (Continued) Others EN 69 Playback Basic playback (cont'd) 6 Select the desired title using [K / L/{ / B], then press [ENTER]. Title mode> <Video List 1 2 3 01/ 01/06 01:00 P12 XP 4 5 6 Pop-up window will appear. 7 8 Select "Play" using [K / L], then press [ENTER]. Playback will start. Press [STOP C] to stop playback. To eject the disc, press [OPEN/CLOSE A] to open the disc tray, then remove the disc. Press [OPEN/CLOSE A] to close the disc tray before turning off the unit. Notes · For DVD-R (Video mode) and DVD-RW (Video mode) discs that are already finalised, a title list will be displayed instead of thumbnails. · If you insert a DVD-RW recorded in VR mode and it has a Playlist, the Playlist is displayed. · You can resume playback from where you stopped playing back the disc (Resume playback). [. . . ]