User manual TOSHIBA D-R150

[. . . ] Introduction DIGITAL VIDEO DVD VIDEO RECORDER D-R150SB OWNER'S MANUAL Connections INSTALLATION GUIDE Read this booklet first. Basic Setup H PM002XXXX010 © 2005 Toshiba Corporation 01_D-R150SB(E)_inst 1 05. 7. 13, 0:23 AM Introduction SAFETY PRECAUTIONS WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. To ensure proper use of this product, please read this owner's manual carefully and retain for future reference. Should the unit require maintenance, contact an authorized service location. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. [. . . ] Connecting to these inputs allows you to enjoy higher quality picture playback. Actual labels for component video inputs may vary depending on the TV manufacturer. (ex. Y, R-Y, R-B or Y, CB, CR) In some TVs or monitors, the color levels of the playback picture may be reduced slightly or the tint may change. To switch the output signal (Progressive/Interlaced) PROGRESSIVE Press PROGRESSIVE on the remote control. The output signal alternates between component progressive and component interlaced. · When "PSO" is displayed on the front panel display, the output signal is progressive. When "PSO" is not displayed, the output signal is interlace. · The following setting is required according to the TV that you are connecting. 4( "Audio out select" on the Setting "AV1 output" on the "Initial settings" menu. page 38 page 40 Basic Setup TV TV or monitor equipped with component video inputs "Video" or "S-Video" "Analog 2ch" · Selecting "RGB" disables signal output from the COMPONENT OUT (Y, PB, PR) jacks. If the on-screen display disappears immediately after you select "RGB", you can restore it by connecting the recorder using the AV OUT VIDEO (yellow) jack. · If you display the setup menu when the output signal is progressive, it automatically changes to interlace. Press PROGRESSIVE again after you exit the menu. Notes · Refer to the owner's manual of the connected TV as well. · When you connect the recorder to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before any connections. · If you place the recorder near a tuner or radio, the radio broadcast sound might be distorted. Be sure to adjust the amplifier's volume to a moderate listening level. Otherwise, the speakers and your hearing may be damaged by a sudden high volume sound. · Turn off the amplifier before you connect or disconnect the recorder's power cord. · Consumers should note that not all high definition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture. In case of 625 progressive scan picture problems, it is recommended that the user switch the connection to the "Standard Definition" output. If there are questions regarding our TV set compatibility with this model 625p DVD player, please contact our Customer Service Center. 17 03_D-R150SB(E)_inst_13-20 17 05. 7. 13, 0:23 AM Connections Connecting a satellite receiver You can connect a satellite receiver to this recorder to enjoy watching or recording satellite programmes through the recorder. By using SCART cable If both your TV and satellite receiver have a SCART input, use a SCART cable to connect the recorder. SCART cable (not supplied) VHF/UHF aerial Satellite receiver To AV2(EXT) To AV1(TV) SCART cable (not supplied) To SCART input To aerial input TV Notes · To watch broadcast programmes by using the satellite receiver, use INPUT SEL. button on the remote control and select "AV2" (this is shown on the display on the recorder). page 38) · According to the type of the TV set that you are connecting, set the output for the AV1(TV) socket. ( · According to the type of video output signal used for the satellite receiver that you are connecting, set "AV2 input" with "Initial settings". [. . . ] ( page 42) 41 06_D-R150SB(E)_inst_40-48 41 05. 7. 13, 0:23 AM Basic Setup C: TV shape setting Select the picture shape according to the aspect ratio of your TV. OPEN/CLOSE ON/STANDBY 1 2 While displaying the setup menu, press shift the cursor to the icon area. to 1 4 7 +10 TIME SLIP DVD 2 5 8 0 TV 3 6 9 CLEAR When the setup menu is not displayed, press EASY NAVI button and select "Setup" using / / / buttons, then press ENTER button. INPUT SEL. Press / to select "Display settings", then press ENTER. e. g. TV VOL T. SEARCH TOP MENU SKIP REV STOP REV CH PROGRESSIVE ENTER MENU SKIP FWD PLAY FWD Display settings TV shape 4:3LB On Screen protector SETUP ADJUST PA US E EA SY VI NA INSTANT REPLAY QUICK DISPLAY ENTER INSTANT SKIP CHP DIVIDE SUBTITLE 3 Press / ENTER. to select "TV shape", then press e. g. ENTER Display settings TV shape 4:3LB On Screen protector 4:3LB 4:3 normal 16:9 wide 16:9 shrink REC REC MODE ZOOM ANGLE TV/DVR Start AUDIO SETUP 42 06_D-R150SB(E)_inst_40-48 42 05. 7. 13, 0:23 AM 4 Press / to select the picture shape. Introduction ENTER 4:3 LB: Select when a standard 4:3 TV is connected. Displays theatrical images with masking bars above and below the picture. When a 4:3 aspect ratio image has been elongated to 16:9 wide picture size, use this setting. Masking bars to the right and left appears. Connections Basic Setup 5 Once the proper setting is selected, press ENTER. The submenu disappears. [. . . ]