User manual TOSHIBA CN30C90

[. . . ] · This TV set may be used only with Toshiba stand listed on page 32. Use with other stands may result in instability, causing possible injury. · Place the TV far enough away from the walls to allow proper ventilation. This will prevent the TV from overheating and avoid possible damage to the TV. [. . . ] ­If the VCR or converter does not respond, repeat steps 1­4 using another code. ­If the VCR or converter does not respond to a different code, you will need to use the remote control that came with your VCR or converter. 3 4 Basic Operation ENT VOL MENU/ ENTER VOL Advanced Operation CH TV CABLE VCR EXIT FAV CH TV/VIDEO A PLAY PIP FF 5 Set the TV/CABLE/VCR switch to TV to control the TV. For future reference, write down the code(s) you used: VCR Code Cable TV Converter Code REC TV/VCR STOP STILL SOURCE SLOW PAUSE REW PIP CH LOCATE SWAP Reference Section Note: You must reprogram the remote control when you change the batteries. These VCRs have a switch labeled "VCR1/VCR2. " If your VCR has this kind of switch and does not respond to the codes for your VCR brand, set the switch to the other position ("VCR1" or "VCR2") and reprogram the remote control. 11 Set up Programming the remote control for use with a non-Toshiba VCR or cable TV converter (continued) In some rare cases, you may not be able to operate your non-Toshiba equipment with your TV remote control. Your other equipment may use a code that is not recognized by the TV remote control. If this happens, you will need to use the remote control provided with your other equipment. Preparation VCR code table BRAND NAME CODE NUMBER BRAND NAME CODE NUMBER BRAND NAME CODE NUMBER Adventura . . . . . . . . . . . . . . . 019, 021, 056, 062, 080, 087, 140, 203, 227, 228, 230, 231, 297, 313, 314, 380, 498 Fisher . . . . . . . . . . . . . . . . . . . . . . 019, 054, 056, 065, 066, 067, 081, 085, 123, 259 Ricoh . . . . . . . . . . . . . . . . . . . . . . 052, 053, 058 Reference Section Advanced Operation Basic Operation 12 Set up Cable TV converter code table BRAND NAME CODE NUMBER BRAND NAME CODE NUMBER Preparation ABC . . . . . . . . . . . . . . . . . . . . . . . . 419 Basic Operation Advanced Operation Reference Section 13 Set up Menu function (general instructions) To adjust any TV feature, you must use the menu function. You can access the menus using the buttons on the TV or remote control. If in doubt, consult your cable company. 17 Set up Watching TV programs or videotapes CHANNEL t/s Selecting a TV channel Select a channel in one of the following two ways: G MENU TV / VIDEO VOLUME CHANNEL Preparation POWER Scan through the programmed channels in numerical sequence: ­ Press CHANNEL s to select the next higher channel. ­ Continue pressing CHANNEL s or t to select the next programmed channel. Select a channel directly: ­ Press the Channel Number buttons (0­9 and 100). To select channel 125, press 100--2--5. G MENU T/S t/s Basic Operation TV/VIDEO RECALL MUTE POWER RECALL If you cannot select a specific channel, make sure the TV/CABLE function is set correctly (see page 16). o 1 4 7 100 2 5 8 0 CH 3 6 9 CH RTN Selecting the video input source Channel Number Advanced Operation You can use the TV/VIDEO button to view a signal coming from other video equipment connected to your TV (such as a VCR or DVD player). See "Connecting your TV" on page 5. Note: To operate your video equipment properly, refer to the instructions provided with the video equipment. ENT 1 VOL Turn the TV and video equipment on. The selected source will be displayed in purple. VOL MENU/ ENTER CHANNEL s/t 2 Reference Section CH TV CABLE VCR TV VIDEO1 VIDEO2 TO SELECT PUSH TV/VIDEO EXIT FAV CH TV/VIDEO A PLAY PIP FF EXIT TV/VIDEO REC TV/VCR STOP 3 Operate the video equipment normally. STILL SOURCE SLOW PAUSE REW PIP CH LOCATE SWAP About the DEMO (demonstration) mode When the DEMO mode is activated, your TV automatically displays a variety of its on-screen menus and special features. To start the demo: 1 Press MENU until the Option menu is displayed on-screen. The onscreen demo starts after about 15 seconds. LANGUAGE:[ENGLISH]FRANCAIS ESPANOL DEMO: [START]STOP C. CAPT: C1 C2 C3 C4 T1 T2 T3 T4[OFF] MOVE[t s] SELECT[T S] To stop the demo: 1 Press EXIT or RECALL on the Remote, or select STOP in the menu. 18 Convenient remote control functions Displaying on-screen information RECALL RECALL MUTE Set up POWER Press RECALL to display the following information on-screen: G o MUTE 1 4 7 100 2 5 8 0 CH 3 6 9 CH RTN G Channel Number G Channel number or VIDEO mode selected (see page 18) Stereo or SAP audio status (see pages 24­25) V-CHIP rating (see pages 28­31) SEE TRO SP A CPIN ATO TX ET T-G VP L V Preparation CBE AL 4 Muting the sound CH RTN ENT VOL MENU/ ENTER VOL Press MUTE to turn off the sound. To restore the sound, press MUTE again. MUTE Basic Operation CH TV CABLE VCR EXIT FAV CH TV/VIDEO A PLAY PIP FF REC TV/VCR STOP Note: When MUTE is pressed, the Closed Captioned feature "C1" is activated ("MUTE" on the screen display will disappear). (This feature functions only when the Closed Caption mode is set to OFF. ) Advanced Operation STILL SOURCE SLOW PAUSE REW PIP CH LOCATE SWAP Changing quickly between two channels The CH RTN function allows you to switch back and forth between the current and previous channels without entering the channel number each time. Reference Section To operate the CH RTN function: 1 2 3 Select the first channel you want to view. The previous channel will return. (Current channel) 4 CH RTN (Previous channel) 6 Each time you press CH RTN, the TV will switch back and forth between the two channels. 19 Set up Adjusting the picture You can adjust the picture quality (CONTRAST, BRIGHTNESS, SHARPNESS, COLOR and TINT) to suit your taste. MENU TV / VIDEO VOLUME CHANNEL Adjusting the picture quality 1 Preparation POWER Press MENU until the Picture 1 menu is displayed on-screen. [. . . ] TACP/THI Authorized Service Center personnel will come to your home when warranty service is required. Depending on the type of repair required, either the service will be performed in your home or the set will be taken to the TACP/THI authorized service center for repair and returned to your home at no cost to you. Limited Two (2) Year Warranty of Picture Tube TACP and THI further warrant the picture tube in this product against defects in materials or workmanship for a period of two (2) years after the date of original retail purchase. During this period, TACP and THI will repair or replace a defective picture tube at their option, with a new or refurbished picture tube, without charge to you, except that, if a defective picture tube is replaced after one (1) year from the date of the original retail purchase, you pay labor charges involved in the replacement. [. . . ]