User manual TOSHIBA B-SA4TP

[. . . ] TOSHIBA Thermal Printer B-SA4TP SERIES Owner's Manual CE Compliance (for EU only) This product complies with the requirements of EMC and Low Voltage Directives including their amendments. VORSICHT: · Schallemission: unter 70dB (A) nach DIN 45635 (oder ISO 7779) · Die für das Gerät Vorgesehene Steckdose muß in der Nähe des Gerätes und leicht zugänglich sein. Centronics is a registered trademark of Centronics Data Computer Corp. As an ENERGY STAR® Partner, TOSHIBA TEC has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. -- Outline of the International ENERGY STAR® Office Equipment Program -The International ENERGY STAR® Office Equipment Program is an international program that promotes energy saving through the penetration of energy efficient computers and other office equipment. The program backs the development and dissemination of products with functions that effectively reduce energy consumption. [. . . ] PRINTER SETUP ENGLISH VERSION EO1-33048 2. 8 Installing the Printer Drivers (5) When the screen which indicates the USB Printing Support driver has been installed, is displayed, click on the [Finish] button. (6) After a while, "TEC B-SA4T" is detected as a new hardware. (7) The "Add New Hardware Wizard" dialog box is displayed. Select "Specify the location of the driver (Advanced)", then click on the [Next] button. E2-37 2. PRINTER SETUP ENGLISH VERSION EO1-33048 2. 8 Installing the Printer Drivers (8) Select "Search for the best driver for your device. Mark the "Specify a location" checkbox, then click on the [Browse] button. Specify "\driver\WinMe-9x" folder, then click on the [Next] button. (9) Check to see that the "TEC B-SA4T" driver is detected, then click on the [Next] button. E2-38 2. PRINTER SETUP ENGLISH VERSION EO1-33048 2. 8 Installing the Printer Drivers (10) Change the printer name if necessary, and select whether or not you use the printer as the default printer ("Yes" or "No"). Click on the [Finish] button. (11) When the screen, which indicates TEC B-SA4T has been installed, is displayed, click on the [Finish] button. (12) When installation is completed, the new printer icon is added in the "Printers" folder. E2-39 2. PRINTER SETUP ENGLISH VERSION EO1-33048 2. 8 Installing the Printer Drivers Windows 2000/XP NOTE: When plug-and-play printer installation in progress is stopped, be sure to delete the printer detected and displayed on the "Device Manager" tab of the "System Properties" dialog box. (1) Log on to your host computer as a member who has full control access privilege concerning the printer settings. (2) Turn the printer ON, then connect it to your host computer with the USB cable. (3) "USB Device" is automatically detected, and "USB Printing Support" is automatically installed. (4) After a while, for Windows XP, "TEC B-SA4T" is detected as a new device. For Windows 2000, "Unknown" device is detected as a new device. In both cases, perform the following steps, though dialog boxes for Windows XP are used. Select "Install from a list or specific location (Advanced)", then click on the [Next] button. E2-40 2. PRINTER SETUP ENGLISH VERSION EO1-33048 2. 8 Installing the Printer Drivers (6) Select "Search for the best driver in these locations". Mark the "Include this location in the search" checkbox, then click on the [Browse] button. Specify the "\driver\WinXP-2000" folder in the CD-ROM, then click on the [Next] button. (7) When the dialog box below is displayed, click on the [Continue Anyway] button. E2-41 2. PRINTER SETUP ENGLISH VERSION EO1-33048 2. 8 Installing the Printer Drivers (8) When the "Completing the Found New Hardware Wizard" screen is displayed, click on the [Finish] button. (9) When installation is completed, the new printer icon is added in the "Printers" folder. E2-42 2. PRINTER SETUP ENGLISH VERSION EO1-33048 2. 8 Installing the Printer Drivers 2. 8. 4. Uninstalling the Printer Driver NOTE: Before uninstalling the printer driver, be sure to complete all of printing, the status monitor, and properties settings. Windows 95/98/ME (1) Select "Settings" ­ "Printers" from the "Start" menu to open the printer folder. (2) Right-click on the printer driver icon to be deleted, then select "Delete". (4) After the printer driver icon is deleted, restart your host computer. Windows NT4. 0 (1) Log on to your host computer as a member who has full control access privilege concerning the printer settings. [. . . ] Please ask a service person of your nearest TOSHIBA TEC service representative. EA2- 5 APPENDIX 3 POWER CORD ENGLISH VERSION EO1-33048 APPENDIX 3 POWER CORD APPENDIX 3 POWER CORD When purchasing the power cord: Since the power cord set is not enclosed in this unit, please purchase an approved one that meets the following standard from your authorized TOSHIBA TEC representative. (As of September 2004) Country Agency Certification mark Country Agency Certification mark Country Agency Certification mark Australia SAA Germany VDE Sweden SEMKKO Austria OVE Ireland NSAI Switzerland SEV Belgium CEBEC Italy IMQ UK ASTA Canada CSA Japan METI UK BSI Denmark DEMKO Netherlands KEMA U. S. A. UL Finland FEI Norway NEMKO Europe HAR France UTE Spain AEE Power Cord Instruction 1. For use with 100 ­ 125 Vac mains power supply, please select a power cord rated Min. For use with 200 ­ 240 Vac mains power supply, please select a power cord rated Min. [. . . ]