User manual TOSHIBA B-SA4TM

[. . . ] TEC Thermal Printer B-SX4T SERIES Owner's Manual CE Compliance (for EU only) This product complies with the requirements of EMC and Low Voltage Directives including their amendments. VORSICHT: · Schallemission: unter 70dB (A) nach DIN 45635 (oder ISO 7779) · Die für das Gerät Vorgesehene Steckdose muß in der Nähe des Gerätes und leicht zugänglich sein. Centronics is a registered trademark of Centronics Data Computer Corp. As an ENERGY STAR® Partner, TOSHIBA TEC has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. -- Outline of the International ENERGY STAR® Office Equipment Program -The International ENERGY STAR® Office Equipment Program is an international program that promotes energy saving through the penetration of energy efficient computers and other office equipment. The program backs the development and dissemination of products with functions that effectively reduce energy consumption. [. . . ] Lower the Print Head Block and set the Ribbon Shaft Holder Plate aligning its holes with the Ribbon Shafts. Wind the leading tape onto the ribbon take-up roll until the ink ribbon can be seen from the front of the printer. Ribbon Shaft Holder Plate 6. Close the Top Cover. T NOTE: Ribbon loss per ribbon saving varies according to the relation between the outer roll diameter of the used ribbon and the print speed. Print speed Ribbon loss/Ribbon saving 3"/sec. 20 mm Auto Ribbon Saving Mode When the auto ribbon saving function is selected, it will be activated to reduce ribbon loss when a no print area extends more than 20 mm (3 or 6 ips) or 30 mm (10 ips). For further information on this function, please ask a TOSHIBA TEC authorised service representative. E2-12 2. PRINTER SETUP ENGLISH VERSION EO1-33034 2. 9 Inserting the Optional PCMCIA Cards 2. 9 Inserting the Optional When the optional PCMCIA Interface Board is installed into the printer, there will be two PCMCIA slots available as shown in the figure below. To protect PC cards, discharge static electricity from your body by touching the metal cabinet of the printer before touching the card. Before inserting or removing a PCMCIA card make sure that the printer's power is turned off. Be sure to protect PCMCIA Cards when not in use by putting them into their protective covers. Do not subject the card to any shocks or excessive force nor expose the card to extremes in temperature or humidity. The card may be inserted into the slot halfway even in the wrong orientation. However, the slot is safety designed so that the card will not seat against the connector pins. This allows the use of Flash Memory type Cards or I/O Cards such as LAN Cards. Make sure that the printer's Power Switch is in the OFF position. Eject Button Slot 1: (Memory type cards only) Slot 2: (I/O type cards such as LAN cards) 2. 3. 4. Model Name Printed Side 3. Slightly pull and fold the Eject Button upward. Eject Button 5. 4. The following PCMCIA cards can be used. Type ATA Card Maker San Disk, Hitachi 3 COM Description A card conforming to the PC card ATA standard 3CCE589ET Series EF-4M-TB CC EF-4M-TB DC FL04M-15-11119-03 IMC004FLSA STI-FL/4A MF84M1-G7DAT01 FJN-004M6C FL04M-20-11138-67 FJP-004M6R MF84M1-GMCAV01 EF-1M-TB AA MF81M1-GBDAT01 Read (See NOTE. ) Remarks ---------Install into the slot (2) only. (This card installed into the slot (1) will not work. ) Read/Write LAN Card NOTE: Reading a read-only-type flash memory is possible if it has been used on the TOSHIBA TEC printer, such as B-472 and B-572. Maxell Maxell Centennial Technologies INC. INTEL Simple Flash Memory TECNOLOGY Card (4 MB) Mitsubishi PC Card KING MAX Centennial Technologies Inc. PC Card Mitsubishi Maxell Flash Memory Card (1 MB) Mitsubishi E2-13 2. PRINTER SETUP ENGLISH VERSION EO1-33034 2. 10 Test Print 2. 10 Test Print A print test should be performed to check that the printer is operating correctly. The following paragraphs guide you through the diagnostic procedure for test label printing. Press and hold the [FEED] and [PAUSE] keys while turning on the printer power switch. [. . . ] In writable character or PC command save mode An error has occurred while writing to flash memory or ATA card. An erase error has occurred in formatting the flash memory or ATA card. 100 Base LAN Board is being initialized. ------------Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes ----No No No Yes No --------- Yes Yes Yes Yes Yes Yes No --------- 15 FLASH WRITE ERR. 16 FORMAT ERROR 17 FLASH CARD FULL Display of error message (See Notes. ) 19 POWER FAILURE 20 INTIALIZING. . . [. . . ]