User manual TOSHIBA 32A50

[. . . ] OWNER'S MANUAL Color Television TM 27A50 32A50 36A50 © TOSHIBA CORPORATION, 2000 Reference Section Advanced Operation Basic Operation Preparation Set up Set up Preparation Dear Customer Congratulations!This manual will help you use the many exciting and useful features to make your TV viewing more enjoyable than ever before. Before operating your TV set, please read all these safety and operating instructions completely and then retain for future reference. Customer's Record You will find the model number and serial number on the back of your TV set. Refer to them whenever you call upon your TOSHIBA dealer regarding this product. [. . . ] (VHF channels 2 through 13 and UHF channels 14 through 69) CABLE: Cable TV signals. (Cable channels 1 through 125) TIMER: 0 MIN TV/CABLE: TV[CABLE] CH PROGRAM ADD/ERASE: [ADD]ERASE V-CHIP CONTROL FAVORITE CH MOVE[t s] SELECT[T S] o CH PROGRAM function 1 4 7 2 5 8 0 CH 3 6 9 CH RTN Channel Number 1 2 Press MENU until the Setup menu is displayed on the screen. Press s or t repeatedly until "CH PROGRAM" is displayed in purple. Reference Section TIMER: 0 MIN TV/CABLE: TV[CABLE] CH PROGRAM ADD/ERASE: [ADD]ERASE V-CHIP CONTROL FAVORITE CH MOVE[t s] START[T S] 100 ENT T/S MENU VOL MENU/ ENTER VOL CH TV CABLE VCR s/t CHANNEL s/t 3 EXIT FAV CH TV/VIDEO A PLAY PIP FF Press T or S to start channel programming. The TV will automatically cycle through all the TV or CABLE channels depending on the mode selected, and store active channels in the channel memory. CH PROGRAM CABLE 24 REC TV/VCR STOP STILL SOURCE SLOW PAUSE REW PIP CH 4 LOCATE SWAP When channel programming is complete, you will see the message at the right. CH PROGRAMMING COMPLETED CABLE 4 5 Press CHANNEL s or t to make sure the channel programming has been done properly. 16 ADD/ERASE function After performing the CH PROGRAM function, you can add or erase specific channels. CABLE channel reference chart Number on this TV Corresponding CABLE channel Number on this TV Corresponding CABLE channel 5 6 5(A-7) 6(A-6) A B C 68 69 68 69 2 3 . . . . . . . . . . . . . . . . . . . . . MOVE[t s] SELECT[T S] 15 16 92 93 94 95 96 97 98 99 100 101 102 . . . . . . . . . . . . . . . . . . . . . 92 93 94 A-5 A-4 A-3 A-2 A-1 100 101 102 . . . . . . . . . . . . . . . . . . . . . MOVE[t s] SELECT[T S] 35 To add the channel Press the button until "ADD" is displayed in purple indicating that the channel has been memorized. 36 TIMER: 0 MIN TV/CABLE: [TV]CABLE CH PROGRAM ADD/ERASE: [ADD]ERASE V-CHIP CONTROL FAVORITE CH MOVE[t s] SELECT[T S] V W AA BB . . . . . . . . . . . . . . . . . . . . . 37 38 . . . . . . . . . . . . . . . . . . . . . 5 Repeat steps 1 to 4 for other channels. You have now completed the channel programming. 60 61 62 63 64 65 66 XX YY ZZ AAA BBB 65 66 123 124 125 123 124 125 The above chart is typical of many cable system channel allocations. If in doubt, consult your cable company. 17 Reference Section Advanced Operation Press T or S : To erase the channel Press the button until "ERASE" is displayed in purple indicating that the channel has been erased from the memory. TIMER: 0 MIN TV/CABLE: [TV]CABLE CH PROGRAM ADD/ERASE: ADD[ERASE] V-CHIP CONTROL FAVORITE CH . . . . . . . . . . . . . . . . . . . . . 34 . . . . . . . . . . . . . . . . . . . . . 4 U Basic Operation Press s or t repeatedly until "ADD/ ERASE" is displayed in purple. TIMER: 0 MIN TV/CABLE: [TV]CABLE CH PROGRAM ADD/ERASE: [ADD]ERASE V-CHIP CONTROL FAVORITE CH 14 . . . . . . . . . . . . . . . . . . . . . Press MENU repeatedly until the Setup menu is displayed on the screen. Preparation 1 Select the channel you want to erase using the CHANNEL L or M button, or select the channel you want to add using the Channel Number buttons. 1 A-8 67 67 Set up Set up Watching TV Programs or Video input CHANNEL t/s Selecting the TV channels Select a channel in one of the following two ways. G To scan the memorized channels in numerical sequence Press CHANNEL s to select the next higher channel. Press the button again to select the next memorized channels. MENU TV / VIDEO VOLUME CHANNEL Preparation POWER G MENU T/S t/s Basic Operation TV/VIDEO To select a channel directly Press the Channel Number buttons (0-9 and 100). To select channel 4, press "4" (or press "0", "4"). To select channel 125, press "100", "2", "5" in sequence. If you cannot select certain channels, either TV (off the air) or CABLE channels Check if the TV/CABLE function is properly set. See page 16. RECALL MUTE POWER RECALL o Selecting the video input source 1 4 7 100 2 5 8 0 CH 3 6 9 CH RTN Advanced Operation Channel Number You can use the TV/VIDEO button to view signal coming from other devices, such as VCR's or video disc players that may be connected to your TV. (See "Connecting Your TV" on page 5. ) Note: To operate your TV and video equipment properly, refer to the instructions furnished with the video equipment. ENT 1 2 VOL Turn the TV and the video equipment ON. Press TV/VIDEO on the Remote Control or on the TV to select "VIDEO 1" or "VIDEO 2". The selected source will be displayed in purple. MENU/ ENTER VOL CHANNEL s/t Reference Section CH TV CABLE VCR TV VIDEO1 VIDEO2 TO SELECT PUSH TV/VIDEO EXIT FAV CH TV/VIDEO A PLAY PIP FF EXIT TV/VIDEO REC TV/VCR STOP STILL SOURCE SLOW PAUSE REW PIP CH 3 Operate the video equipment normally. LOCATE SWAP About the Demonstration Mode When this function is activated, your TV will automatically display a variety of its on-screen menus and special features. This function is provided for demonstration purposes only. 1 2 Press MENU, then s or t until "DEMO" in the Option menu is displayed in purple. The on-screen demonstration will start after about 15 seconds. LANGUAGE:[ENGLISH]FRANCAIS ESPANOL DEMO: [START]STOP C. CAPT: C1 C2 C3 C4 T1 T2 T3 T4[OFF] MOVE[t s] SELECT[T S] To stop the demonstration Press EXIT or RECALL on the Remote or select "STOP" in the menu. 18 Displaying on-screen information RECALL RECALL MUTE POWER Press RECALL to display the following onscreen information. G G G MUTE 1 4 7 100 2 5 8 0 CH 3 6 9 CH RTN CABLE 4 Channel Number Muting the sound CH RTN ENT VOL MENU/ ENTER VOL CH TV CABLE VCR MT UE EXIT FAV CH TV/VIDEO A PLAY PIP FF REC TV/VCR STOP STILL SOURCE SLOW PAUSE REW PIP CH LOCATE SWAP Changing quickly between two channels Press CH RTN to return to the last channel viewed. This allows you to view two programs without entering an actual channel number each time. To operate this function 1 2 3 Select the first channel you want to view. (Viewing channel) Select the other channel with the Channel Number buttons. Press CH RTN. The previous channel will return. (Previous channel) 4 Each time you press CH RTN, the TV will switch back and forth between the two channels. 6 19 Reference Section Advanced Operation Note: When the MUTE button is pressed, the ClosedCaptioned feature "C1" is activated. ("MUTE" on the screen display will disappear. ) To deactivate, press the MUTE button again. (This feature only functions when the Closed Caption mode is set to "OFF". ) Basic Operation Press MUTE to mute the sound. To restore the sound, press MUTE again. Preparation o Channel number or VIDEO mode selected Stereo or SAP audio status V-CHIP rating STEREO SAP CAPTION TEXT TV-PG L V Set up Convenient Remote Functions Set up Adjusting the Picture You can adjust the picture quality (CONTRAST, BRIGHTNESS, SHARPNESS, COLOR and TINT) to suit your taste. MENU TV / VIDEO VOLUME CHANNEL Adjusting the picture quality 1 Preparation POWER Press MENU repeatedly until the Picture 1 menu is displayed on the screen. Press s or t until the item you want to adjust is displayed in purple. 2 MENU CONTRAST ­ BRIGHTNESS ­ SHARPNESS ­ COLOR ­ ­ TINT RESET MOVE[t s] ADJUST[T S] + + + + + T/S t/s 3 Basic Operation Press T or S to adjust the level. [. . . ] Commercial Units Products sold and used for commercial use have a limited ninety (90) day warranty for all parts, labor and picture tube. Owner's Manual and Demographic Card You should read this owner's manual thoroughly before operating this product. You should complete and mail the enclosed Demographic card within ten days after you, or the person who has given you this product as a gift, purchased this product. This is one way to enable TACP/THI to provide you with better customer service and improved products. [. . . ]