User manual TOSHIBA 32A41

[. . . ] Set up Preparation OWNER'S MANUAL Color Television ® Basic Operation Advanced Operation Reference Section 32A41 36A41 © 2001 TOSHIBA CORPORATION All Rights Reserved. Owner's Record The model number and serial number are on the back of your TV. Refer to these numbers whenever you communicate with your Toshiba dealer about this TV. Model number: Serial number: Important Information Set up WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Precautions Installing your TV · Place the TV on the floor or on a sturdy platform. If you install the TV on a soft floor, make sure that the floor is not damaged by the weight of the TV. [. . . ] Model 32A41 is used for illustration purposes. Preparation MENU TV / VIDEO VOLUME CHANNEL The following are general instructions for using the menu system: 1 POWER Repeatedly press MENU to select a menu (Picture, Audio, Setup, or Option, as shown below). The menus automatically disappear from the screen if no adjustments are made within 15 seconds. To clear an on-screen menu instantly, press EXIT on the remote control. 2 MENU T/S t/s Basic Operation 3 4 RECALL MUTE POWER RECALL 1 o Picture 1 3 6 9 CH RTN CONTRAST ­ BRIGHTNESS ­ SHARPNESS ­ COLOR ­ ­ TINT RESET + + + + + 2 5 8 0 CH Advanced Operation 4 7 100 Picture 2 ENT COLOR MOVE[t s] ADJUST[T S] TEMPERATURE:[COOL]MEDIUM WARM PICTURE PREFERENCE: [NORMAL]THEATER MEMORY MTS: MOVE[t s] SELECT[TBASS S] TREBLE BALANCE SURROUND [STR]SAP MONO ­ ­ ­ [ON]OFF Audio T/S Reference Section VOL MENU/ ENTER VOL s/t + + + Setup MENU TV CABLE VCR CH TIMER: 0 MIN MOVE[t s] SELECT[T TV/CABLE: S] TV[CABLE] CH PROGRAM ADD/ERASE: [ADD]ERASE V-CHIP CONTROL FAVORITE CH MOVE[t s] SELECT[T S] DEMO: C. CAPT: EXIT FAV CH TV/VIDEO A PLAY PIP FF EXIT Option REC TV/VCR STOP STILL SOURCE SLOW PAUSE REW PIP CH LANGUAGE:[ENGLISH]FRANCAIS ESPANOL START[STOP] C1 C2 C3 C4 T1 T2 T3 T4[OFF] LOCATE SWAP MOVE[t s] SELECT[T S] Note: The T/S buttons function as VOLUME T/S buttons when no menu is on-screen. The s/t buttons function as CHANNEL s/t buttons when no menu is on-screen. Models 32A41 and 36A41 do not have PIP features. 14 First-time operation VOLUME T/S Set up Turning the TV set on 1 MENU TV / VIDEO VOLUME CHANNEL Set the TV/CABLE/VCR switch on the remote control to TV. To turn the TV off, press POWER again. TV 4 2 POWER Preparation MENU T/S t/s POWER 3 Press VOLUME T/S to adjust the volume. To decrease the volume, press T . Basic Operation VOLUME ­ TO CONTROL PUSH VOL + RECALL MUTE POWER o POWER 3 1 4 7 100 2 5 8 0 CH Advanced Operation 6 Selecting the on-screen display language 9 CH RTN 1 s/t ENT Press MENU until the Option menu is displayed on-screen. Press s or t repeatedly until "LANGUAGE" is displayed in purple. 2 LANGUAGE:[ENGLISH]FRANCAIS ESPANOL DEMO: START[STOP] C. CAPT: C1 C2 C3 C4 T1 T2 T3 T4[OFF] VOL MENU/ ENTER VOL MOVE[t s] SELECT[T S] Reference Section CH TV CABLE VCR EXIT FAV CH TV/VIDEO A PLAY PIP FF T/S VOLUME T/S 3 Press T or S until your desired language is displayed in purple. For example, if you select FRANCAIS, the menu display language changes to French. REC TV/VCR STOP LANGUAGE: ENGLISH[FRANCAIS] ESPANOL DEMO: MARCHE[ARRET] S. TITRA: C1 C2 C3 C4 T1 T2 T3 T4[ARRET] STILL SOURCE SLOW PAUSE REW PIP CH BOUGER[t s] CHOISIR[T S] LOCATE SWAP Understanding the Auto Power Off feature The TV automatically turns off after 15 minutes if it is tuned to a vacant channel or a station that has completed its broadcast for the day. This feature does not operate when the TV is in VIDEO mode. Understanding the Last Mode Memory feature If the power is cut off while you are viewing the TV, the Last Mode Memory feature automatically turns the TV on when the power is resupplied. If the power is going to be off for a long time and you are going to be away from your TV, unplug the power cord to prevent the TV from turning on in your absence. 15 Set up Programming the channel memory The channel memory is the list of TV channels your TV stops on when you press CHANNEL L/M. First, use the TV/CABLE and CH PROGRAM functions (below) to program all active channels in your area into the channel memory. Then use the ADD/ERASE function (page 17) to add/erase individual channels in the memory. CHANNEL t/s Preparation TV/CABLE function 1 MENU TV / VIDEO VOLUME CHANNEL Press MENU until the Setup menu is displayed on-screen. Press s or t until TV/CABLE is displayed in purple. 2 POWER TIMER: 0 MIN TV/CABLE: [TV]CABLE CH PROGRAM ADD/ERASE: [ADD]ERASE V-CHIP CONTROL FAVORITE CH MOVE[t s] SELECT[T S] Basic Operation 3 MENU T/S t/s Press T or S until the mode that corresponds to your TV signal system displays in purple. TV: TV broadcast signals (VHF channels 2 through 13 and UHF channels 14 through 69) TIMER: 0 MIN TV/CABLE: TV[CABLE] CH PROGRAM ADD/ERASE: [ADD]ERASE V-CHIP CONTROL FAVORITE CH MOVE[t s] SELECT[T S] Advanced Operation RECALL MUTE POWER CABLE: Cable TV signals (Cable channels 1 through 125) o 1 4 7 2 5 8 0 CH 3 6 9 CH RTN Channel Number CH PROGRAM function Use the CH PROGRAM function to automatically add all active channels to the channel memory. Reference Section 100 ENT 1 2 s/t CHANNEL s/t Press MENU until the Setup menu is displayed on-screen. Press s or t repeatedly until "CH PROGRAM" is displayed in purple. T/S MENU VOL MENU/ ENTER VOL TIMER: 0 MIN TV/CABLE: TV[CABLE] CH PROGRAM ADD/ERASE: [ADD]ERASE V-CHIP CONTROL FAVORITE CH MOVE[t s] START[T S] CH TV CABLE VCR EXIT FAV CH TV/VIDEO A PLAY PIP FF 3 REC TV/VCR STOP STILL SOURCE SLOW PAUSE REW PIP CH LOCATE SWAP Press T or S to start channel programming. The TV automatically cycles through all the TV or CABLE channels (depending on the mode selected), and stores the active channels in the channel memory. When channel programming is done, you will see the message, "Ch Programming Completed. " Press CHANNEL s or t to scan through the programmed channels. 4 5 CH PROGRAM CABLE 24 CH PROGRAMMING COMPLETED CABLE 4 16 Set up ADD/ERASE function After using the CH PROGRAM function to automatically program channels into the channel memory, you can use the ADD/ERASE function to manually add or erase individual channels, as follows: CABLE channel reference chart Number on this TV Corresponding CABLE channel Number on this TV Corresponding CABLE channel 1 5 6 A-8 5(A-7) 6(A-6) A B C 67 68 69 67 68 69 Preparation 1 Select the channel you want to add or erase. If you are adding a channel, you must use the Channel Number buttons to select the channel. . . . . . . . . . . . . . . . . . . . . . 2 3 Press MENU until the Setup menu is displayed on-screen. Press s or t until ADD/ERASE is displayed in purple. TIMER: 0 MIN TV/CABLE: [TV]CABLE CH PROGRAM ADD/ERASE: [ADD]ERASE V-CHIP CONTROL FAVORITE CH MOVE[t s] SELECT[T S] 14 15 16 . . . . . . . . . . . . . . . . . . . . . Basic Operation 92 93 94 95 96 97 98 99 100 101 102 . . . . . . . . . . . . . . . . . . . . . 92 93 94 A-5 A-4 A-3 A-2 A-1 100 101 102 . . . . . . . . . . . . . . . . . . . . . 4 To add the channel: Press T or S until ADD is displayed in purple, indicating that the channel has been added to the channel memory. To erase the channel: Press T or S until ERASE is displayed in purple, indicating that the channel has been erased from the channel memory. TIMER: 0 MIN TV/CABLE: [TV]CABLE CH PROGRAM ADD/ERASE: ADD[ERASE] V-CHIP CONTROL FAVORITE CH MOVE[t s] SELECT[T S] . . . . . . . . . . . . . . . . . . . . . 34 35 36 . . . . . . . . . . . . . . . . . . . . . U V W AA BB . . . . . . . . . . . . . . . . . . . . . Advanced Operation TIMER: 0 MIN TV/CABLE: [TV]CABLE CH PROGRAM ADD/ERASE: [ADD]ERASE V-CHIP CONTROL FAVORITE CH MOVE[t s] SELECT[T S] 37 38 . . . . . . . . . . . . . . . . . . . . . Reference Section 5 6 Repeat steps 1­4 for other channels. Press s or t to select another item in the menu, or press EXIT on the remote control to return to viewing. 60 61 62 63 64 65 66 XX YY ZZ AAA BBB 65 66 You have now finished programming the channel memory. 123 124 125 123 124 125 The above chart is typical of many cable system channel allocations. [. . . ] Rental Units The warranty for rental units begins with the first rental or thirty (30) days from the date of shipment to the rental firm, whichever comes first. Commercial Units Products sold and used for commercial use have a limited ninety (90) day warranty for all parts, labor and picture tube. Owner's Manual and Demographic Card You should read this owner's manual thoroughly before operating this product. You should complete and mail the enclosed Demographic card within ten days after you, or the person who has given you this product as a gift, purchased this product. [. . . ]