User manual TOSHIBA 32A32

[. . . ] Introduction Connecting your TV OWNER'S MANUAL Color Television ® Using the Remote Control Setting up your TV Using the TV's Features 32A32 32A42 32A42A 36A42 © 2002 TOSHIBA CORPORATION All Rights Reserved. TOSHIBA AM E CONSUMER CA P RI TS, INC. DUC RO Appendix O 140 Owner's Record The model number and serial number are on the back of your TV. Refer to these numbers whenever you communicate with your Toshiba dealer about this TV. A 9 45 6 IS Dear Customer, Thank you for purchasing this Toshiba TV. [. . . ] When automatic channel programming is complete, the message "CH Programming Completed" appears. Press CHANNEL to view the programmed channels. VOL MENU/ ENTER VOL yz x · CH Using the Remote Control TV CABLE VCR CHANNEL yz EXIT EXIT Adding and erasing channels manually After you have automatically programmed the channels into the TV's memory, you can manually add and erase individual channels. If you are adding a channel, you will need to use the CHANNEL NUMBERS to select the channel. Press y or z to highlight ADD/ERASE. Setting up your TV SET UP LANGUAGE: [ENGLISH] FRANCAIS ESPANOL TV/CABLE: [TV] CABLE CH PROGRAM Using the TV's Features ADD/ERASE: V-CHIP CONTROL MORE MOVE [ ] [ADD] ERASE SELECT [ ] 5. Press x or · to highlight ADD or ERASE, whichever function you want to perform. Repeat steps 1­6 for other channels you want to add or erase, or press EXIT to return to normal TV viewing. Appendix Changing channels To change to the next programmed channel: Press CHANNEL y z. To change to a specific channel (programmed or unprogrammed): Press the CHANNEL NUMBERS (0­9 and 100). Note: For channels 100 and higher, press the 100 button, and then the next two channel numbers (for example, to select channel 100, press 100, 0, 0; to select channel 125, press 100, 2, 5). 17 Using the TV's features Adjusting the channel settings Switching between two channels You can switch between two channels without entering an actual channel number each time. To switch between two channels: 1. Every time you press CH RTN, the TV will switch back and forth between the last two channels you tuned the TV to. RECALL MUTE POWER o 1 4 7 100 2 5 8 0 CH 3 6 9 CH RTN CHANNEL NUMBERS ENT CH RTN MENU VOL MENU/ ENTER VOL yz x · Programming your favorite channels The Favorite Channel feature allows you to use the FAV CH buttons on the remote control to cycle through your favorite channels, skipping over channels you do not normally watch. Note: You can still use CHANNEL to cycle through all the channels you previously programmed into the TV's memory (see "Programming channels in to the TV's memory" on page 16). To program your favorite channels: 1. Press y or z to highlight FAVORITE CH. SET UP CH TV CABLE VCR CHANNEL yz EXIT EXIT FAV CH TV/VIDEO A PLAY PIP FF REC TV/VCR STOP FAV CH zy STILL SOURCE SLOW PAUSE REW PIP CH LOCATE SWAP CT-90037 Using the TV's Features MORE TIMER: DEMO: 0 MIN START [STOP] FAVORITE CH MOVE [ ] START [ ] 5. Press EXIT. SET UP FAVORITE CH [SET ] CLEAR 2 5 6 11 0 0 0 0 0 0 0 0 [TV: CYAN, CABLE: BLUE] SELECT [ ] SET [ ] 9. (Continued on next page) 18 Introduction To select your favorite channels: Press FAV CH zy on the remote control to cycle through the favorite channels you programmed. Note: The FAV CH zy buttons will not work unless you program at least one favorite channel. Tune the TV to the channel you want to clear from your favorite channel list. Press x or · to highlight CLEAR. MENU CH VOL MENU/ ENTER VOL yz x · CH TV CABLE VCR Connecting your TV EXIT FAV CH TV/VIDEO A PLAY PIP FF EXIT REC TV/VCR STOP FAV CH zy STILL SOURCE SLOW PAUSE REW PIP CH LOCATE SWAP Using the Remote Control SET UP CT-90037 FAVORITE CH SET [CLEAR] 2 5 6 0 0 0 0 0 0 0 0 0 [TV: CYAN, CABLE: BLUE] SELECT [ ] CLEAR [ ] 7. Repeat steps 1­8 for other channels you want to clear from your favorite channel list. Setting up your TV Using the V-Chip Control (blocking) feature You can use the V-Chip Control feature to block certain programs or channels, to prevent others from viewing them. Selecting a PIN code Before you can block programs or channels, you must select a personal identification number (PIN) code. Your PIN code allows you to access the V-Chip Control menu, and prevents others from changing the rating and blocking limits you set. To select your PIN code and access the V-Chip Control menu: 1. Press x or · to display the new PIN code entering screen. Using the TV's Features Appendix SET UP LANGUAGE: [ENGLISH] FRANCAIS ESPANOL TV/CABLE: [TV] CABLE CH PROGRAM ADD/ERASE: [ADD] ERASE SET UP BLOCKING IS RESET PLEASE ENTER NEW PIN CODE ____ V-CHIP CONTROL MORE MOVE [ ] START [ ] SELECT [0­9] END [EXIT] 19 5. After the code is entered, the V-Chip Control menu appears. SET UP RECALL MUTE POWER o RECALL 1 4 7 2 5 8 0 CH 3 6 9 CH RTN ENABLE BLOCKING [Y] N SET RATING SET BLOCKING OPTIONS NEW PIN CODE BLOCK CHANNEL CHANNEL NUMBERS MOVE [ ] SELECT [ ] V-Chip Control (Blocking) Menu 100 ENT MENU 6. Press x or · to highlight "Y, " which enables all blocking by activating the V-Chip. See "Blocking programs by ratings" on page 21, "Blocking unrated movies and programs" on page 23. Note: The "Blocking channels" feature (page 24) is not affected by the "Enable Blocking" setting. VOL MENU/ ENTER VOL yz x · CH TV CABLE VCR To disable blocking: Highlight "N" in step 7, above, to deactivate the V-Chip Control feature and disable blocking. EXIT EXIT Changing your PIN code 1. [. . . ] DURING THIS PERIOD, TCL WILL, AT TCL'S OPTION, REPAIR OR REPLACE A DEFECTIVE PICTURE TUBE WITH A NEW OR REFURBISHED PICTURE TUBE WITHOUT CHARGE TO YOU, EXCEPT THAT, IF A DEFECTIVE PICTURE TUBE IS REPAIRED OR REPLACED AFTER ONE (1) YEAR FROM THE DATE OF THE ORIGINAL RETAIL PURCHASE, YOU PAY LABOR CHARGES INVOLVED IN THE REPAIR OR REPLACEMENT. Rental Units The warranty for rental units begins with the date of first rental or thirty (30) days from the date of shipment to the rental firm, whichever comes first. *Commercial Units Televisions sold and used for commercial purposes have a limited ninety (90) day warranty for all parts, labor, and picture tubes. (4) Labor service charges for set installation, setup, adjustment of customer controls, and installation or repair of antenna systems are not covered by these warranties. [. . . ]