User manual TOSHIBA 32A10

[. . . ] OWNER'S MANUAL Color Television TM 27A10 32A10 36A10 © TOSHIBA CORPORATION, 2000 Reference Section Advanced Operation Basic Operation Preparation Set up Set up Preparation Dear Customer Congratulations!This manual will help you use the many exciting and useful features to make your TV viewing more enjoyable than ever before. Before operating your TV set, please read all these safety and operating instructions completely and then retain for future reference. Customer's Record You will find the model number and serial number on the back of your TV set. Refer to them whenever you call upon your TOSHIBA dealer regarding this product. [. . . ] If you select "FRANCAIS" for example, the display language changes to French. LANGUE: DEMO: S. TITRA: ENGLISH[FRANCAIS] ESPANOL MARCHE[ARRET] C1 C2 C3 C4 T1 T2 T3 T4[ARRET] Advanced Operation Press MENU until the Option menu is displayed on the screen. Basic Operation Press VOLUME T S to adjust the volume. To decrease the volume, press T . Preparation Set up Programming Channel Memory Set up The channel memory is the list of TV channel numbers your TV will stop on when you press the CHANNEL v or w button. First, use the TV/CABLE and CH PROGRAM functions to preset all active channels in your area. If necessary, arrange the preset channels with the ADD/ERASE functions so that you can tune into only desired channels. CHANNEL t s TV/CABLE function Preparation 1 MENU TV/VIDEO VOLUME CHANNEL POWER Press MENU until the Setup menu is displayed on the screen. Press s or t until "TV/CABLE" is displayed in purple. 2 TIMER: 0 MIN TV/CABLE: [TV]CABLE CH PROGRAM ADD/ERASE: [ADD]ERASE V-CHIP CONTROL FAVORITE CH MOVE[t s] SELECT[T S] 3 Basic Operation MENU TS ts RECALL MUTE POWER Press T or S until the mode that corresponds to your TV signal system is displayed in purple. (VHF channels 2 through 13 and UHF channels 14 through 69) CABLE: Cable TV signals. (Cable channels 1 through 125) TIMER: 0 MIN TV/CABLE: TV[CABLE] CH PROGRAM ADD/ERASE: [ADD]ERASE V-CHIP CONTROL FAVORITE CH MOVE[t s] SELECT[T S] o CH PROGRAM function Advanced Operaion 1 4 7 100 2 5 8 0 CH 3 6 9 CH RTN Channel Number 1 2 Press MENU until the Setup menu is displayed on the screen. Press s or t repeatedly until "CH PROGRAM" is displayed in purple. TIMER: 0 MIN TV/CABLE: TV[CABLE] CH PROGRAM ADD/ERASE: [ADD]ERASE V-CHIP CONTROL FAVORITE CH MOVE[t s] START[T S] ENT TS VOL Reference Section MENU/ ENTER VOL MENU TV CABLE VCR CH st CHANNEL st 3 EXIT FAV CH TV/VIDEO A PLAY PIP FF Press T or S to start channel programming. The TV will automatically cycle through all the TV or CABLE channels depending on the mode selected, and store active channels in the channel memory. CH PROGRAM CABLE 24 REC TV/VCR STOP STILL SOURCE SLOW PAUSE REW PIP CH 4 LOCATE SWAP When channel programming is complete, you will see the message at the right. CH PROGRAMMING COMPLETED CABLE 4 5 Press CHANNEL s or t to make sure the channel programming has been done properly. 16 ADD/ERASE function After performing the CH PROGRAM function, you can add or erase specific channels. CABLE channel reference chart Number on this TV Corresponding CABLE channel Number on this TV Corresponding CABLE channel 1 2 3 5 6 5(A-7) 6(A-6) A B C 68 69 68 69 . . . . . . . . . . . . . . . . . . . . . Press s or t repeatedly until "ADD/ ERASE" is displayed in purple. TIMER: 0 MIN TV/CABLE: [TV]CABLE CH PROGRAM ADD/ERASE: [ADD]ERASE V-CHIP CONTROL FAVORITE CH MOVE[t s] SELECT[T S] 14 15 16 92 93 94 95 96 97 98 99 100 101 102 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Press MENU repeatedly until the Setup menu is displayed on the screen. 92 93 94 A-5 A-4 A-3 A-2 A-1 100 101 102 . . . . . . . . . . . . . . . . . . . . . Press T or S : To erase the channel Press the button until "ERASE" is displayed in purple indicating that the channel has been erased from the memory. TIMER: 0 MIN TV/CABLE: [TV]CABLE CH PROGRAM ADD/ERASE: ADD[ERASE] V-CHIP CONTROL FAVORITE CH MOVE[t s] SELECT[T S] . . . . . . . . . . . . . . . . . . . . . 34 35 . . . . . . . . . . . . . . . . . . . . . 4 U V W AA BB . . . . . . . . . . . . . . . . . . . . . To add the channel Press the button until "ADD" is displayed in purple indicating that the channel has been memorized. TIMER: 0 MIN TV/CABLE: [TV]CABLE CH PROGRAM ADD/ERASE: [ADD]ERASE V-CHIP CONTROL FAVORITE CH MOVE[t s] SELECT[T S] 36 37 38 . . . . . . . . . . . . . . . . . . . . . 5 Repeat steps 1 to 4 for other channels. 61 62 63 64 65 66 YY ZZ AAA BBB 65 66 123 124 125 123 124 125 The above chart is typical of many cable system channel allocations. If in doubt, consult your cable company. 17 Reference Section You have now completed the channel programming. 60 XX Advanced Operation Basic Operation Preparation Select the channel you want to erase using the CHANNEL v or w button, or select the channel you want to add using the Channel Number buttons. 1 A-8 67 67 Set up Watching TV Programs or Video input Set up Selecting the TV channels TV/VIDEO CHANNEL t s Select a channel in one of the following two ways. q To scan the memorized channels in numerical sequence Press CHANNEL s to select the next higher channel. Press the button again to select the next memorized channels. MENU TV/VIDEO VOLUME CHANNEL POWER Preparation q MENU TS ts To select a channel directly Press the Channel Number buttons (0-9 and 100). To select channel 4, press "4" (or press "0", "4"). To select channel 125, press "100", "2", "5" in sequence. If you cannot select certain channels, either TV (off the air) or CABLE channels Check if the TV/CABLE function is properly set. See page 16. Basic Operation RECALL MUTE POWER RECALL o Selecting the video input source 1 4 7 100 2 5 8 0 CH 3 6 9 CH RTN Channel Number You can use the TV/VIDEO button to view signal coming from other devices, such as VCR's or video disc players that may be connected to your TV. (See "Connecting Your TV" on page 5. ) Note: To operate your TV and video equipment properly, refer to the instructions furnished with the video equipment. ENT Advanced Operaion 1 2 VOL Turn the TV and the video equipment ON. Press TV/VIDEO on the Remote Control or on the TV to select "VIDEO 1" or "VIDEO 2". The selected source will be displayed in purple. MENU/ ENTER VOL CHANNEL st CH TV CABLE VCR T V VDO IE1 VDO IE2 TO SELECT PUSH TV/VIDEO EXIT FAV CH TV/VIDEO A PLAY PIP FF EXIT TV/VIDEO Reference Section REC TV/VCR STOP STILL SOURCE SLOW PAUSE REW PIP CH 3 Operate the video equipment normally. LOCATE SWAP About the Demonstration Mode When this function is activated, your TV will automatically display a variety of its on-screen menus and special features. This function is provided for demonstration purposes only. 1 2 Press MENU, then s or t until "DEMO" in the Option menu is displayed in purple. The on-screen demonstration will start after about 15 seconds. LANGUAGE:[ENGLISH]FRANCAIS ESPANOL DEMO: [START]STOP C. CAPT: C1 C2 C3 C4 T1 T2 T3 T4[OFF] MOVE[t s] SELECT[T S] To stop the demonstration Press EXIT or RECALL on the Remote or select "STOP" in the menu. 18 Convenient Remote Functions Displaying on-screen information RECALL RECALL MUTE POWER Press RECALL to display the following onscreen information. q o MUTE 1 4 7 100 q CBE AL 4 5 8 0 CH 6 9 CH RTN Channel Number Muting the sound CH RTN ENT CH TV CABLE VCR MT UE EXIT FAV CH TV/VIDEO A PLAY PIP FF REC TV/VCR STOP STILL SOURCE SLOW PAUSE REW PIP CH Note: When the MUTE button is pressed, the Closed-Captioned feature "C1" is activated. ("MUTE" on the screen display will disappear. ) To deactivate, press the MUTE button again or press Volume to restore the sound. (This feature only functions when the Closed Caption mode is set to "OFF". ) LOCATE SWAP Changing quickly between two channels Press CH RTN to return to the last channel viewed. [. . . ] Commercial Units Products sold and used for commercial use have a limited ninety (90) day warranty for all parts, labor and picture tube. Owner's Manual and Demographic Card You should read this owner's manual thoroughly before operating this product. You should complete and mail the enclosed Demographic card within ten days after you, or the person who has given you this product as a gift, purchased this product. This is one way to enable TACP/THI to provide you with better customer service and improved products. [. . . ]