User manual TOSHIBA 20HLV85

[. . . ] Introduction Connecting your TV/DVD Setting up your TV/DVD Using the TV/DVD's Features DVD Playback Appendix ENER Y STAR PARTNER DIGITAL VIDEO 17HLV85 20HLV85 5U90121A(E)Cover 1 6/27/05, 1:53 PM Introduction Always read and understand the PRODUCT WARNINGS and USER DIRECTIONS that are contained in this manual before attempting to use your television, to help ensure its safe use. Always store this manual near your television for convenient future reference. NOTE TO CATV INSTALLERS This is a reminder to call the CATV system installer's attention to Article 820-40 of the NEC, which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to grounding system of the building, as close to the point of cable entry as practical. For additional antenna grounding information, see item 17 on page 4. Dear Customer, Thank you very much for purchasing this Toshiba television. You must carefully read and understand all of the safety instructions contained in this manual before you attempt to use this product in order to avoid potential hazards that could cause bodily injury or property damage or could damage your Television. [. . . ] After the GameTimer is programmed, the display will appear briefly every ten minutes to remind you that the GameTimer is operating. When the programmed time is reached, the TV/DVD will change channels automatically and enter VIDEO LOCK mode. LOCKS LOCK CH LOCK VIDEO LOCK OFF GAME TIMER :SELECT :ADJUST Connecting your TV/DVD Channel Numbers Setting up your TV/DVD OFF OFF / 30 / 60 / 90 / 120 Enter Using the panel lock feature You can lock the top panel buttons to prevent your settings from being changed accidentally (by children, for example). When the panel lock is in ON, all control buttons on the TV/DVD top panel (except POWER) do not operate. Use the Channel Number buttons (0-9) to enter your password, then press ENTER. Press or to highlight PANEL LOCK and press or to highlight LOCKS ON. ON / OFF If a button on the top panel is PANEL LOCK NEW PASSWORD pressed, the message "NOT AVAILABLE" appears. :SELECT :ADJUST Using the Using the TV/DVD's Features TV/DVD's Features Exit Menu TV/DVD top panel VOLUME DVD Playback To unlock the panel: Press and hold the VOLUME button on the TV/DVD top panel for about 10 seconds until the message "PANEL LOCK:OFF" appears on-screen. Use the Channel Number buttons (0-9) to enter your password, then press ENTER. Press or to highlight PANEL LOCK, and then press or highlight OFF. Appendix to 29 5U90121A(E)P26-30 29 6/17/05, 11:00 AM Labeling channels Channel labels appear above the channel number display each time you turn on the TV/DVD, select a channel, or press the DISPLAY button. Press the button repeatedly until the character you want appears on the screen. If you would like a blank space in the label name, you must choose CH LABEL an empty space from the list of SET characters; otherwise, a dash will LABEL RETURN appear in that space. Press EXIT to return to normal viewing. OPTION :SELECT CH LABEL LABEL RETURN :SELECT Channel Numbers OFF ON TIMER FAVORITE CH CH LABEL VIDEO LABEL :ADJUST :CH002 Enter SET / CLEAR :ADJUST ENTER :SET Exit Menu :CH002 ENTER :SET Note: The character will change as below. Using the TV/DVD's Features SPACE + To erase channel labels: 1. Repeat steps 1-6 to erase other channel labels. 30 5U90121A(E)P26-30 30 6/20/05, 4:07 PM Introduction Selecting the video input source Press INPUT to view a signal from another device connected to your TV/ DVD, such as a VCR or DVD player. You can select ANT, VIDEO 1, VIDEO 2, ColorStream HD, HDMI or PC depending on which input jacks you used to connect your devices (see "Connecting your TV/DVD" on page 11). SOURCE SELECTION 0. ANT VIDEO1 VIDEO2 ColorStream HD HDMI PC [0-5] : SELECT Pressing INPUT on the remote control displays the current signal source (press INPUT again or 0-5 to change) Please note the following regarding the HDMI source selection: The HDMI IN jack is not intended for connection to and should not be used with a PC (personal computer). See "Connecting an HDMI or a DVI device to the HDMI input" on page 17 and "Connecting a PC" on page 20 for details. Connecting your TV/DVD You also can use the Channel M / ?In addition to cycling through your programmed channels (page 24), the Channel M / ?buttons will also cycle through the video input sources, in the order illustrated below. ANT (programmed channel) PC HDMI VIDEO1 VIDEO2 GAME ColorStream HD Labeling the video input sources The video label feature allows you to label each input source for your TV/DVD from the following preset list of labels: : Uses the default label name VCR : Video cassette recorder DVD : DVD video DTV : Digital TV set-top box SAT : Satellite box CBL : Cable box To label the video input sources: 1. Press EXIT to return to normal viewing. Setting up your TV/DVD INPUT Using the Using the TV/DVD's Features TV/DVD's Features OPTION ON TIMER FAVORITE CH CH LABEL VIDEO LABEL OFF / OFF / SET :SELECT :ADJUST Exit Menu VIDEO LABEL 1. VIDEO1 2. VIDEO2 3. ColorStream 4. HDMI - / VCR / DVD / DTV S AT / C B L - HD :SELECT :ADJUST DVD Playback Setting the clock You must set the clock before you can program the ON timer. Press or to set the hour, then press to highlight the minute position. Press or to set the minutes, then press EXIT to return to normal viewing. SETUP LANGUAGE CLOCK SET TV / CABLE CH PROGRAM ADD / ERASE ENGLISH 12:00AM CABLE ADD Note: If the power source for the TV/DVD is interrupted (for example, the power cord is unplugged or a power failure occurs), you will need to reset the clock. :SELECT :ADJUST SETUP LANGUAGE CLOCK SET TV / CABLE CH PROGRAM ADD / ERASE ENGLISH 8:30AM CABLE ADD Appendix :SELECT :ADJUST 31 5U90121A(E)P31-32 31 6/17/05, 11:00 AM Setting the ON timer This feature allows you to program the TV/DVD to turn on automatically at a set time. If you program the ON TIMER to "DAILY, " the TV/DVD will turn on every day at the same time to the same channel until you clear the ON TIMER. To set the on timer: (Example: Turning on the TV/DVD to channel 012 at 6:30 AM, DAILY) 1. [. . . ] *Limited Warranty for Commercial Units TCL warrants LCD TV/DVD units sold and used for commercial purposes as follows: all parts are warranted against defects in materials or workmanship for a period of ninety (90) days after the date of original purchase. DURING THIS PERIOD, TCL WILL, AT TCL'S OPTION, REPAIR OR REPLACE A DEFECTIVE PART WITH A NEW OR REFURBISHED PART WITHOUT CHARGE TO YOU. YOU MUST DELIVER THE ENTIRE TELEVISION TO AN AUTHORIZED TCL SERVICE DEPOT. YOU MUST PAY FOR ALL TRANSPORTATION AND INSURANCE CHARGES FOR THE TELEVISION TO AND FROM THE SERVICE DEPOT. [. . . ]