User manual TORNADO TO7465

[. . . ] Use the vacuum cleaner only for its intended use as described in these instructions. Change the dust bag before it is full in order to maintain the best efficiency. Do not use the vacuum cleaner to pick up matches, live ashes or cigarette butts. [. . . ] Avoid picking up hard, sharp objects with the vacuum cleaner as they may damage the cleaner parts. Switch the vacuum cleaner off at the machine before unplugging from the electrical outlet. Grasp the plug to disconnect cord from electrical outlet before changing the dust bag. If your vacuum cleaner is not operating correctly, switch off the power supply and consult an authorized service agent. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard. WARNING 1. The hose should be checked regularly and must not be used if damaged. 1 DJ68-00093J 6/17/02 12:59 PM Page 3 IDENTIFICATIONS OF PARTS REMOTE POWER CONTROL * (REMOTE CONTROL TYPE ONLY) HOSE * HANDLE * SUCTION REGULATOR * CYCLONIC FILTER * CORD REWIND BUTTON TRANSPARENT TUBE * AUTO BUTTON POWER CONTROL SWITCH * ON/OFF BUTTON TUBE * FLOOR NOZZLE * TOOL STORAGE COVER BUTTON FOR SUCTION HOSE REMOVAL DUST COVER CLAMPER FOR DUST BAG COMPARTMENT CARRYING HANDLE Features marked with * may vary according to model. w 2 DJ68-00093J 6/17/02 12:59 PM Page 4 ASSEMBLING THE VACUUM-CLEANER READY FOR USE 1) Connect the suction hose to the suction tube. 2) Adjust the suction tube(depending on model). x EXTENDING : Holding the narrow part of the telescopic tube with one hand, push the handle in the opposite direction with your other hand. 2) Remove the dust bag from the cleaner 3) After removing the used dust bag, insert the cardboard bag collar of the new dust bag into its original position. 4) Press the dust cover down gently until the clamper relocks. NOTE : Used dust bags can be sealed by removing the film from the paper and sticking over the suction opening. FOR CLOTH FILTER BAG After using, if the cloth filter bag is full of dust, clean the cloth filter bag and use it again. DUST-FULL INDICATOR If the "Dust-Full" indicator switch changes to "RED" while you are cleaning, the dust bag is full and must be replaced. NOTE : If the "Dust-Full" indicator continues to display "RED" even after changing the dust bag, turn the cleaner off and check whether the hose, tube or nozzle is clogged. 7 DJ68-00093J 6/17/02 12:59 PM Page 9 CYCLONIC FILTER (ONLY CYCLONIC FILTER TYPES) You can use a dust bag in your cleaner for a long time thanks to the Cyclonic Filter system and it maintain the maximum cleaning efficiency. The larger particle of dust filtered from Cyclonic Filter remain in Dust Barrel when suctioned air and dust revolves in the Cyclonic Filter. When the Dust Barrel is filled with dust up to the indicating line, it needs disposing and cleaning. After cleaning the Dust Barrel and Cyclonic Filter, connect the Cyclonic Filter with extension wand and handle(washed part should be dried in the shade throughly before assembling. ) 5. Adjust indicating marks each other carved on Dust Barrel and Cyclonic Filter. CYCLONIC FILTER CREVICE TOOL DUST BARREL 8 DJ68-00093J 6/17/02 12:59 PM Page 10 MAINTENANCE OR REPLACEMENT OF THE FILTERS INLET FILTER v v The secondary filter, located behind the grille in the back of dust bag compartment, protects the motor from dirt particles. After cleaning the secondary filter attach it in place. NOTE : The filters must be completely dried before being replaced in the dust compartment. OUTLET FILTER For Micro Filter Type Open the dust cover and lift off the grille. For HEPA Filter Type HEPA Filter Grille Filter Micro Filter Preliminary Filter Grasp filter and pull it out with preliminary filter. After cleaning preliminary filter, reposition new filter and preliminary filter by reversing this procedure. Preliminary Filter Grasp grille filter and pull it out with preliminary filter. [. . . ] After cleaning the secondary filter attach it in place. NOTE : The filters must be completely dried before being replaced in the dust compartment. OUTLET FILTER For Micro Filter Type Open the dust cover and lift off the grille. For HEPA Filter Type HEPA Filter Grille Filter Micro Filter Preliminary Filter Grasp filter and pull it out with preliminary filter. After cleaning preliminary filter, reposition new filter and preliminary filter by reversing this procedure. Preliminary Filter Grasp grille filter and pull it out with preliminary filter. After cleaning preliminary filter, reposition new filter compartment and preliminary filter by reversing this procedure. 9 DJ68-00093J 6/17/02 12:59 PM Page 11 USAGE OF FLOOR NOZZLE FOR RUG / FLOOR SELECTOR Before use make sure that the position of the selector is in the right position for the type of surface to be cleaned. Select the carpet indicator when cleaning carpets. [. . . ]