User manual TORNADO TO3400

[. . . ] If it still does not fit, contact a qualified electrician to replace the outlet. Do not change the plug in any way. 1 DJ68-00075A 2001. 7. 52:24PM 3 Assembling Parts Assembled Vacuum Cleaner Parts 1-1 The assembled cleaner will look like the illustration to the left. 1. Handle 2. ON/OFF switch 3. Quick release cord hook 4. Exhaust filter 5. Crevice tool 6. Handle release 7. Carrying handle 8. Hose 9. Extension wand 10. Combination tool 11. Power control (some models only) Front Back WARNING! OPERATE THE VACUUM CLEANER ONLY AT THE VOLTAGE SPECIFIED ON THE NAMEPLATE. Step 1. Attaching the Handle 1-2 Stand the vacuum upright and slide the base of the handle firmly into the grooves at the top of the vacuum body. 1-3 Insert the screw provided into the existing hole. [. . . ] Attaching the Handle 1-2 Stand the vacuum upright and slide the base of the handle firmly into the grooves at the top of the vacuum body. 1-3 Insert the screw provided into the existing hole. Before securing the handle, please check that the handle is fitted to the vacuum body and make sure there's no gap. Step 2. Attaching the Hose and Tools 1-4 Slide the end of the hose wand with tabs into the suction intake valve. 1-5 Slide the extension wand and the crevice tool together into the storage clip. 2 DJ68-00075A 2001. 7. 52:24PM 4 Operation 2-1 2-2 2-3 ON-OFF Switch 1. To turn cleaner ON(I), press the ON/OFF switch to the ON position. 2. To the cleaner OFF(O), press the ON/OFF switch to the OFF position. Handle positions The handle of your cleaner has three positions; upright for storage and when using cleaning tools; operating for general operation on carpet and floors; low for reaching under low furniture. Step on handle release pedal to lower handle. Transporting cleaner To move your cleaner from room to room, put the handle in upright position, tilt the cleaner back on its rear wheels and push forward. 2-4 2-5 A B C Carrying handle The cleaner can also be moved by using the carrying handle. Cleaning Tool attachments Attachment tools can be used to clean furniture or drapes, on stairs or in corners. Place the vacuum on the floor with the handle in the upright position. while using attachment tools. Do not place the vacuum on top of furniture or steps as the brushroller may cause damage. Combination tool: Two types of cleaning tools are included in one attachment: rotate for desired tool. ·Use brush side to dust furniture, blinds, books, lamps, shelves. ·Use upholstery side for curtains, draperies, cushions, fabrics. Do not operate cleaner without either the secondary or final filter in place. Check agitator shield Because your cleaner picks up so well, we strongly recommend you check for debris accumulation under the agitator shield each time you clean the filters. Removing debris under the shield will help maintain your cleaner's excellent pick up and suction. Remove any debris and replace shield, agitator and bottom plate (Figs. 3-13 to 3-15). 4 DJ68-00075A 2001. 7. 52:24PM 6 Maintenance The belt The belt on your cleaner causes the agitator to rotate and is important for the effective operation of the cleaner. The belt is located under the bottom plate of the cleaner and should be checked from time to time to be sure it is in good condition. 3-7 3-8 When to replace Disconnect cleaner from electrical outlet. To check belt, remove bottom plate as shown in "How to replace. " Replace belt it is stretched, cut or broken. How to replace Disconnect cleaner from electrical outlet. Place handle in low position and turn cleaner over so bottom side is up. Remove the 4 screws as shown with a screw driver. Remove agitator and used belt. Discard used belt. 3-9 3-10 3-11 With lettering on outside of belt and positioned as shown in box on (D), slide new belt over motor pulley (B). Insert agitator through belt and place belt in belt guide (C) on agitator. Should the agitator shield (D) become dislodged while replacing the belt or the agitator, reposition it as shown, noting the placement of its belt guide (D) Grasp agitator firmly and fit it into position by first sliding the end opposite the belt into the rectangular slot (F) on side of cleaner. [. . . ] Discard used belt. 3-9 3-10 3-11 With lettering on outside of belt and positioned as shown in box on (D), slide new belt over motor pulley (B). Insert agitator through belt and place belt in belt guide (C) on agitator. Should the agitator shield (D) become dislodged while replacing the belt or the agitator, reposition it as shown, noting the placement of its belt guide (D) Grasp agitator firmly and fit it into position by first sliding the end opposite the belt into the rectangular slot (F) on side of cleaner. Turn agitator, making sure belt is not pinched between agitator and agitator shield. 3-12 When to replace the agitator brush roll When agitator brushes are worn, the agitator should be replaced. To check condition of brushes, disconnect cleaner from electrical outlet. [. . . ]