User manual TORNADO T7726 INSTALLATION INSTRUCTIONS

[. . . ] Do not vacuum anything that is burning or smoking such as cigarettes, matches or hot ashes. Toner, such as that used in printers and photocopiers can conduct electricity. Do not use to pick up any flammable or combustible liquids, such as gasoline, or use in areas where they may be present. Do not pull or carry by the cord, use the cord as a handle, close a door on the cord, or pull the cord around sharp edges or corners. [. . . ] If moisture gets into the appliance there is a risk of electric shock. SAVE THESE INSTRUCTIONS 7 Guide to the vacuum cleaner 8 Guide to the vacuum cleaner a Hand piece b Suction power buttons + / ­ c On/Off button for Powerbrush with LED d Standby button with LED for vacuum pauses e Power level display f Lock release button g Electro Telescopic wand h Electro Telescopic wand release button i Elbow j Dust compartment lid release k Dust compartment filter (motor protection) l Dust bag m Powerbrush (depending on model SEB 217 or SEB 236) n Carrying handle o Fastener for the powerbrush outlet cap p Park-System (on both sides of the vacuum) q Active HEPA filter r Cord rewind switch s Power cord t Exhaust filter display and Reset button u Thermo indicator , v Park-System w Standby indicator x Foot switch On/Off s y Accessory compartment lid release z Dustbag change indicator 9 Before using the vacuum cleaner Connecting the Electro hose ^ Insert the elbow into the suction socket until it clicks. Use the inlet guides to direct insertion. Disconnecting the Electro hose ^ Press the release buttons at the sides of the elbow and lift the hose from the socket. 10 Before using the vacuum cleaner Connecting handpiece and Electro Telescopic wand ^ Insert the handpiece into the electro telescopic wand until it clicks. ^ To release the handpiece from the telescopic wand press the locking button (see arrow) and pull the handpiece away from the telescopic wand. Adjusting the Electro Telescopic suction wand One part of the electro telescopic wand is fitted inside the other and can be adjusted to your height for comfortable vacuum cleaning. ^ Press the telescopic wand release button (see arrow) to release the tubes and adjust to the required height. 11 Before using the vacuum cleaner Using the Powerbrush The Powerbrush is particularly suitable for cleaning and restoring crushed carpet pile of wall to wall carpeting and floor coverings subject to hard wear, especially in high traffic areas. The standard floor brush or the Miele parquet floorbrush should be used to clean delicate hard flooring and floor surfaces susceptible to scratching. Do not use the powerbrush on: ­ Floors with a variable or uneven surface. ­ High quality, hand knotted rugs, for example Berber or Persian rugs, as well as extremly long piled area rugs and carpets. Turn the Powerbrush off to vacuum these types of floor coverings and use only suction. Connecting the Electro Telescopic wand and the Powerbrush ^ Insert the Electro Telescopic wand, pointing down, into the Powerbrush until it clicks into place. For more information on use and maintenance please refer to the instructions supplied with the Powerbrush. 12 Before using the vacuum cleaner Using the floor brush Observe the cleaning instructions of the floor manufacturer. The floor brush is suitable for cleaning carpets, rugs, and hard surfaces. For flooring susceptible to scratching, use one of the special Miele floor brushes (see "Optional accessories"). Connecting the Electro Telescopic wand to a floor tool ^ Fit the Electro Telescopic wand firmly into the floor tool. If the marker completely fills the indicator window, the dust bag needs to be changed. How the dustbag change indicator works The dustbag change indicator is designed to show when the bag is full of common household dust and measures the amount of air flow through the dustbag. Normal household dust is a mixture of dust, hair, carpet fluff, threads, sand, etc. However, if fine dust, such as drill dust, sand, plaster or flour is vacuumed, the pores of the dustbag may become blocked. The marker will indicate that the bag is "full" even when it is not. The dustbag should be changed as the suction power is greatly reduced. This is because the air flow of the dustbag may still be high enough not to activate the marker to show maximum. The dustbag should still be changed. 24 Maintenance and care How to change the dustbag ^ Lift the release button for the dust compartment lid and raise the lid until it clicks into place. ^ Grasp the collar by the two finger holes and pull it out from the dustbag holder. The dustbag has a flap which closes automatically to prevent dust from escaping when the dustbag is removed. ^ Insert the new dust bag as far as it will go into the dustbag holder. Keeping it folded will prevent it from getting caught when the dust compartment lid is closed. Take care not to jam the dust bag in the lid. , An empty-operation-barrier blocks the dust compartment lid from closing if no dustbag is inserted or if it is not inserted all the way. Do not force it closed! 25 Maintenance and care When to change the exhaust filter Always change the ACTIVE HEPA filter when the filter change indicator (Reset button) lights. [. . . ] A heavily soiled exhaust or dust compartment filter can also be the cause of overheating. ^ Check for any blockages and allow the vacuum to cool for 30 minutes. 32 Technical Service In the event of a fault which you cannot fix yourself please contact the Miele Service Department at the phone number on the back of this booklet. This can be found on the data plate on the bottom of the vacuum. 33 Optional accessories Some models come equipped with one or more of the following accessories. Turbobrush Observe the cleaning instructions of the floor manufacturer. [. . . ]