User manual TOPCOM DIABLO 100/TWIN/TRIPLE/QUATTRO FULL VERSION

[. . . ] You have to dispose of the batteries in an environment friendly manner according to your country regulations. DE F AB C 1 Disposal of the device (environment) 1 GH 2 3 MN O I 4 12 5 JKL PQ 5 6 R WX YZ S 7 TU V 8 9 0 4 R/INT M1 At the end of the product lifecycle, you should not throw this product into the normal household garbage but bring the product to a collection point for the recycling of electrical and electronic equipments. Some of the product materials can be re-used if you bring them to a recycling point. By reusing some parts or raw materials from used products you make an important contribution to the protection of the environment. Please contact your local authorities in case you need more information on the collection points in your area. Cleaning Clean the telephone with a slightly damp cloth or with an anti-static cloth. [. . . ] After finishing your call, press the On-hook key to hang up. 5. 2 Incoming calls to answer the When a call comes in, the handset will start to ring. To end the call press the On-hook button. 5. 3 Programming memory numbers You can program 10 indirect numbers (of max. The first entry will be shown on the display Press and hold the Memory button until the -icon appears on the display. Enter the location (0-9) where you want to store the telephone number under. If you wish to insert a pause, press the Redial/Pause button you want a pause of 3 sec. /P on the location where 5. 4 Calling a memory number Press the Memory button Scroll with the Up/Down keys to the entry you want to dial (0-9). Press the Onhook button to terminate the call. 4 Topcom Diablo 100/Twin/Triple/Quattro Topcom Diablo 100/Twin/Triple/Quattro 5. 5 Direct access memory (Key 1, 2, 3 and M1) ENGLISH The product has 3 locations (Key `1', `2' and `3') where you can store a number under and dial it by pressing and holding one of these keys in standby. The phone will automatically take the line and dial the number which is stored under this key. The number stored under key `1' can also be dialed out by pressing the `M1'-key shortly in standby. 5. 5. 1 Programing the direct memory keys Press the Memory button short. Press and hold the Memory button until the -icon appears on the display. Press and hold one of the 3 direct memory keys (Key 1, 2 or 3) where you want to store the number under until `Sx - _' appears. To leave the direct memory programming, press the On-hook button . 5. 6 Mute function It is possible to deactivate the microphone during a conversation. to deactivate or activate the microphone. 5. 7 Setting the volume . You can set the During a conversation you can set the volume by pressing the scroll button volume between 1-5. 5. 8 Paging When you press the Paging button on the base unit, the handset emits a ringing signal for 20 seconds. Press any key to stop the ringing on all handsets. 5. 9 Flash button (R) When you press the R button, also called flash or recall, the unit generates a line interruption (of 100 ms or 250 ms). It gives you the possibility to use the special services of your telephone provider and/or to transfer calls when you have a telephone exchange. You can change the flash time if needed (See "Setting the Flash time" on page 6). 5. 10 Programming procedure You can change the ring melodie, volume, day, time etc. . . by going into the program procedure: To go into the program procedure you have to press and hold the Program button until the icon starts to flash. Each time you press the Program button you will confirm the previous setting and jump to the next setting: External ring volume/melody Dial mode setting Internal ring volume/melody Date/time setting Flash time setting Base ring volume/melody 5. 10. 1 Handset External melody and volume Press and hold the Program button until the icon starts to flash. Press the Program button again, the external melody is heard and the EXT-icon is flashing. Use the scroll keys to select the desired volume (Off or 1-5) Press again to confirm the setting and to go to the next setting below. 5. 10. 2 Handset Internal melody and volume The internal melody is heard and the INT-icon is flashing. [. . . ] When the handset is registered, it will show the handset number followed by the time. 8 Call transfer and Intercom between two handsets These functions only work when more then one handset (like a Twin/Triple/Quattro version) is registered to the base! 8. 1 Call transfer and conference call during an external call During an external call, press and hold the INT key until INT appears . The other handset will start to ring: ­ When the other handset takes the line you can talk internally. If you hang up, the external line will be connected with the other handset. If you press the `#'-key you can talk with the 2nd handset and external line at the same time (conference call) ­ Or press and hold the INT key again to return to the external call. [. . . ]