User manual TNB NEEC012

[. . . ] Mention of software products manufactured by other companies does not necessarily constitute endorsement by Oki Printing Solutions. While all reasonable efforts have been made to make this document as accurate and helpful as possible, we make no warranty of any kind, expressed or implied, as to the accuracy or completeness of the information contained herein. The most up-to-date drivers and manuals are available from the Oki Printing Solutions web site: http:// www. okiprintingsolutions. com Oki, TNB Printing Solutions and Microline are registered trademarks of Oki Electric Industry Company, Ltd. Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corporation. [. . . ] Turn the power OFF, verify that the carriage moves properly, then turn the power ON again. If the problem is still there after you turn the power ON again, contact your dealer. High temperature alarm status Operating instructions > 28 Indicator MENU Status ON OFF Flashing Meaning Menu printing mode Normal printing mode High temperature indication Quiet print mode Normal speed printing mode High multipart printing mode Printer power is ON Printer power is OFF Low power consumption mode QUIET ON OFF Flashing POWER ON OFF Flashing Button switches Switch SEL Status On-line Off-line SHIFT Function Sets the printer to off-line Sets the printer to on-line and disalarms the printer Used only in conjunction with one of the following buttons: SEL, LF, FF/ LOAD, PARK, TEAR described below. Holding the button down results in continuous line feeding. LF Off-line Operating instructions > 29 Switch FF/LOAD Status On-line and offline Continuous Forms mode On-line and offline Cut sheet manual mode Function Continuous form fed until first line of next page Ejects the cut sheet TEAR On-line Continuous Forms mode Delivers the continuous form to the cut position. If the button is pressed again or data is received, the original form position is restored. Ineffective On-line Cut sheet manual mode Off-line PARK Continuous Forms mode Ineffective If the continuous form is in position, press to retract the form to the Pin Tractors. (If the sprocket holes of the last page of the form disengage from the sprocket pins, do not attempt to eject the paper as a paper jam may result. ) SHIFT+SEL Enters menu mode Operating instructions > 30 Switch SHIFT+LF Status Function Microfeed (0. 14 mm step) down Hold this button combination down for continuous feeding or ejecting of paper. SHIFT+FF/ LOAD Microfeed (0. 14 mm step) up Hold this button combination down for continuous feeding or ejecting of paper. SHIFT+PARK On-line Off-line Ineffective Saves the set paper start position (first line print position). Quieter print mode Each press of the button pair progresses the printer through Quieter print mode > High multipart print mode > Normal print mode SHIFT+TEAR On-line Off-line Ineffective Operating instructions > 31 Setting menu values The following information explains the printer settings and how you can change them. Printer items and their values are printed for reference. Confirming current settings To print the current menu settings, use a cut sheet of lettersize paper or continuous forms of width at least 254 mm. Carry out one of the following: (a) (b) If the printer power is OFF, while holding down the SEL button set the printer Power Switch to ON. If the printer power is ON, press the SHIFT and SEL buttons together. 3. To save this position as the TOF, press the SEL button to set the printer off-line and press and hold down the SHIFT and PARK buttons for 3 seconds. Note Do not turn the Platen Knob or switch off the printer during the above procedure. Quick printer settings Printer impact mode When switched ON, the printer enters the impact mode selected in the menu. You can change this to normal speed and quiet printing without using the menus as follows. Normal speed printing Use this for standard file printing operations. 1. Hold down the SHIFT button and press the TEAR button. The QUIET indicator turns off. Quiet printing Use this for quieter printing. 1. Hold down the SHIFT button and press the TEAR button. The QUIET indicator is illuminated. Operating instructions > 41 Emphasis printing CAUTION! Do not use emphasis printing if performing horizontal tab character printing on thin paper as the paper may become damaged. Use this for printing multipart forms. You have to set emphasis printing by using the menus to set Impact Mode to Hi Copy as described in "Menu setting" on page 33. Notes If the paper on top is so thick that duplication on the paper below it fails, use emphasis printing. The print may become blurred if high density characters and graphics are printed using a new ribbon. In emphasis mode, ensure that the paper is flat to avoid possible printing errors. Operating instructions > 42 Troubleshooting Clearing paper jams Cut sheet paper jammed in printer WARNING! Do not carry out any operations inside the printer with the Power Switch set to ON. 1. Set the Paper Thickness lever to the Replace Ribbon position (position 10). WARNING! The Print Head may be hot after printing. Rotate the Platen Knob in the relevant direction and pull the cut sheet out from the front or rear of the printer. [. . . ] The paper length selected in the application does not match the physical paper length. Load forms with their left holes in line with the right ones. Relocate the Pin Tractors to tighten the paper. Move the paper to make it straight. Cancel the skip over perforation spacing. Match the paper length selected in the application with the physical paper length in use. Select the paper length in number of lines in the application. Troubleshooting > 54 Problem Cause Action Abnormal switchover between cut sheet and continuous forms modes. [. . . ]