User manual TNB CHNB19V120

[. . . ] Extension cords do not guarantee the required safety of the appliance (e. g. To guarantee the electrical safety of this appliance continuity must exist between the appliance and an effective grounding system. If there is any doubt, have the electrical system of the house checked by a qualified electrician. ~ Before installation or service, ~ Do not use an extension cord to ~ Be certain your appliance is 4 IMPORTANT SAFETY INSTRUCTIONS Installation and connected in compliance with the installation instructions. ~ The dishwasher must be installed ~ , WARNING - Fire hazard ~ Installation and repair work should be performed by a Miele authorized service technician. Work by unqualified persons could be dangerous and may void the warranty. [. . . ] Replacing the insert b ^ Slide the hitches of the insert under the struts of the lower basket. ^ Push down on the handle to snap the insert into position. This insert is ideal for cups, glasses, plates, bowls, pots and pans. ^ The stemguard can be used to hold the stems of glassware or coffee cup handles. 22 Loading the dishwasher Vase / Bottle insert (depending on model) Removing the insert a: ^ To remove the insert, gently pull the handle upwards. ^ Slide the hitches of the insert under the struts of the lower basket. ^ Place the insert into the lower basket as shown in the illustration. The item will not be properly cleaned. 23 Basket accessories Additional inserts for the upper and lower baskets may be purchased from your Miele dealer or Miele. Depending on the model some accessories come standard with the machine. Glassware insert GGO To wash long stemmed glassware attaches to the upper basket To wash saucers, baby bottles and small items To wash the parts of the Cappuccinatore To wash tall glassware in the lower basket To wash large plates with a maximum diameter of approx. 13 3/4" (35 cm). Multi-function basket GMFO Cappuccinatore insert GCEO Tall glassware insert GGU Large diameter plate insert GTLU 35 24 Use Detergent You can use powder, gel or tab detergents. Detergent tabs are not recommended for use with the program "Express". The tabs may not dissolve completely. , Dishwasher detergents contain irritant and corrosive ingredients. The "Intake / Drain" indicator flashes four times in intervals. The setting can be recognized by the flashing of the "SaniWash" indicator: ­ flashing: buzzer is activated ­ not lit up: buzzer is deactivated ^ To change the setting press the "Program" button for at least one second, until the "Intake / Drain" indicator lights up. ^ Turn the dishwasher off "o". 30 Additional options Default settings All settings can be reset to the factory default. ^ Press and hold the "Program" button and at the same time turn the dishwasher on "g". Hold the "Program" button until the "Rinse & Hold" program indicator comes on. The "Intake / Drain" indicator flashes once long and twice short in intervals. The setting can be recognized by the flashing of the "SaniWash" indicator: ­ flashing: all settings are factory default ­ not lit up: at least one setting was changed ^ To change the setting press the "Program" button for at least one second, until the "Intake / Drain" indicator lights up. ^ Turn the dishwasher off "o". 31 Frequently asked questions With the aid of the following guide, minor problems can be fixed without a service call. , Repairs should only be carried out by a qualified and trained person in accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage. Technical faults Problem The program does not start. ­ Contact Miele Technical Service. The drain pump is running when the door is opened. The waterproof system has activated. 32 Frequently asked questions Problems with water Intake / Drain Problem Shortly after the program start the dishwasher stops running. The "Intake / Drain" indicator flashes when the door is open. [. . . ] ^ Carefully reinsert the non-return valve and secure it with the locking clamp. ^ Tilt the locking clamp to the side a. ^ Remove all foreign objects from the non-return valve. , Make sure the locking clamp clicks into place! 49 50 Installation Instructions Please refer to the Installation Diagram supplied with these instructions. To comply with IEC sound testing protocols, please contact Miele for additional instructions. Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information. Electrical connection , Installation, repairs and other work by unqualified persons could be dangerous. Check that the voltage, frequency and fuse rating shown on the data plate match the household mains supply. [. . . ]