User manual TJERNLUND 950-4020 I, IL, XL MOTOR KIT 8504051 REV 2 1196
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual TJERNLUND 950-4020 I, IL, XL MOTOR KIT 8504051 REV 2 1196. We hope that this TJERNLUND 950-4020 I, IL, XL MOTOR KIT 8504051 REV 2 1196 user guide will be useful to you.
Manual abstract: user guide TJERNLUND 950-4020 I, IL, XL MOTOR KIT 8504051 REV 2 1196
Detailed instructions for use are in the User's Guide.
[. . . ] TJERNLUND PRODUCTS, INC.
1601 Ninth Street · White Bear Lake, MN 55110-6794 PHONE (800) 255-4208 · (651) 426-2993 · FAX (651) 426-9547 Visit our web site · www. tjernlund. com
MODEL I, IL, XL REPLACEMENT MOTOR KIT
1. [. . . ] Refer to the installation instructions of your unit for proper maintenance procedures. Position motor onto motor mount, being sure motor shaft (with shaft extension) is fitted into Draft Inducer wheel. Firmly fasten motor to motor mount with wrench, using proper bolts, washers and nuts removed in step 2. Secure Draft Inducer wheel by tightening set screw(s) onto shaft extension. Spin the wheel by hand to ensure proper alignment and equal blade clearance on both housing sides. If appropriate circuit does not appear, consult Tjernlund Products, Inc. All wiring must be done in accordance with the NEC and applicable codes. The wiring from the appliance should be protected by overcurrent protection(fuses or circuit breakers) rated 15 amperes or less, as applicable for 14 AWG conductors. [. . . ] Oil holes or lances are provided at front and rear faces of motor.
GAS WIRING TO ANY APPLIANCE EQUIPPED WITH 24V CONTROLS NO POST-PURGE RELAY/TIMER ON DRAFT INDUCER
COMPONENTS NEEDED: (1) DRAFT INDUCER (1) PS1505 FAN PROVER (1) 24/115V RELAY USE 950-1040 FOR MODELS DJ3 & D3 USE 950-1016 FOR MODELS I, IL, XL
DRAFT INDUCER CONNECTED TO OIL BURNER WITH R8184G CONTROLS (DRAFT INDUCER MOTOR LESS THAN 4. 4 AMPS) INCLUDES MODELS UP TO THE D3
COMPONENTS NEEDED: (1) DRAFT INDUCER (1) PS1505 FAN PROVER (1) 950-1067 RELAY/TIMER MAXIMUM AMP LOAD IS 4. 4 AMPS USE DIAGRAM BELOW IF DRAFT INDUCER MOTOR IS GREATER THAN 4. 4 AMPS
DRAFT INDUCER CONNECTED TO OIL BURNER WITH R8184G CONTROLS (DRAFT INDUCER MOTOR GREATER THAN 4. 4 AMPS) INCLUDES THE MODELS I, IL, XL
COMPONENTS NEEDED: (1) DRAFT INDUCER (1) PS1505 FAN PROVER (1) 950-1067 RELAY/TIMER MAXIMUM AMP LOAD IS 4. 4 AMPS (1) HONEYWELL R4222B1082 RELAY OR EQUIVALENT (INSTALLER SUPPLIED)
REV. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE TJERNLUND 950-4020 I, IL, XL MOTOR KIT 8504051 REV 2 1196
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual TJERNLUND 950-4020 I, IL, XL MOTOR KIT 8504051 REV 2 1196 will begin.
