User manual THRUSTMASTER FERRARI WIRELESS F430 COCKPIT

[. . . ] - Recover the wireless receiver (14) found in the lower section of the battery compartment. 6/20 SWITCHING THE WHEEL ON OR OFF - Position the switch (located on the right-hand side of the wheel): - To ON for switching on the wheel. Important note: When you switch on your wheel, it must always be perfectly centred physically (to prevent any misalignment). Set the PC/PS3 switch (17) of the receiver (14) to the “PS3” position. [. . . ] AUTOMATIC CALIBRATION OF THE WHEEL AND PEDALS - The centre of the wheel is preset as soon as you turn it on: it is therefore vital for the wheel to be perfectly aligned on its axis when you switch it on. To do this, position the wheel in perfect alignment with the centre, and then simultaneously press “SELECT + START + ENGINE START” (this operation must be carried out each time the wheel is switched on). - The steering of the wheel and the pedals automatically self-calibrate. 13/20 ADVANCED FUNCTIONS ADJUSTING THE WHEEL’S SENSITIVITY Your wheel’s steering has 2 sensitivity modes: - “Normal Sensitivity” (default mode and recommended on PC - requires setting on PS3) - “High Sensitivity” (default mode and recommended on PS3 - requires setting on PC) Setting “Normal Sensitivity” mode (default mode and recommended on PC) Action - Set the Manettino switch to the relevant icon. Your wheel’s steering is now at Normal Sensitivity ON Setting “High Sensitivity” mode (default mode and recommended on PS3) Action - Set the Manettino switch to the relevant icon. Your wheel’s steering is now more sensitive, especially at the centre ON CONFIGURING THE PEDALS Your wheel’s accelerator and brake controls are in “separate” mode by default, meaning that the pedals function on independent axes. This mode lets you considerably improve the precision of your steering. If you game does not support the “separate” mode, the pedal set of the wheel will not work correctly. SETTING Simultaneously press and release both pedals (accelerator and brake) + the PEDAL SET MODE SEPARATE (recommended mode for most games) COMBINED or DOES NOT FLASH FLASHES button. 14/20 CONFIGURING THE PEDALS ON PLAYSTATION® 3 Separate pedal set (default mode) Combined pedal set (must be set) - Accelerator = R2 trigger of the PS3 gamepad - Brake = L2 trigger of the PS3 gamepad - Accelerator = Up direction of the “right mini-stick” of the PS3 gamepad - Brake = Down direction of the “right mini-stick” of the PS3 gamepad CONFIGURING THE PEDALS ON PC Separate pedal set (default mode) Combined pedal set (must be set) - Accelerator = RZ axis - Brake = Y axis - Accelerator = Up direction of the Y axis - Brake = Down direction of the Y axis 15/20 PROGRAMMING THE WHEEL AND PEDALS Your wheel is fully programmable: - All the action buttons can be switched between themselves. - All the action buttons can be programmed onto the pedals or gearshift paddles. TWO PROGRAMMING MODES The button and the PRESET LED allow you to view the programming type chosen: AUTOMATIC (pre-programmed) or MANUAL (programmed by yourself). Simply pressing this button allows you to switch from one programming mode to another (even during a game). “AUTOMATIC PRESET” (PRESET This is the default programming. BUTTON OFF) For more information, refer to the diagrams in CONFIGURING “AUTOMATIC PRESET” - PLAYSTATION® 3 / PC. “MANUAL PRESET” (PRESET BUTTON ON) This is your personal programming. The buttons can either be: - programmed onto the pedals or gearshift paddles - or switched between each other. - The programming is automatically saved in the wheel (even when it is disconnected or switched off). Press and release the MAPPING button Press and release the button to programme. LED status On On Flashing Off 4 Press and release the button, the gearshift paddle or pedal you want to assign to this function. On Your “MANUAL PRESET” programming is now enabled and updated (with your programming applied). 16/20 EXAMPLES OF POSSIBLE USES: - On PS3 , programme L2/R2 or L3/R3 onto the Up and Down gearshift paddles (L1/R1 by default). [. . . ] Contents, designs and specifications are subject to change without notice and may vary from one country to another. ENVIRONMENTAL PROTECTION RECOMMENDATION At the end of its working life, this product should not be disposed of with standard household waste, but rather dropped off at a collection point for the disposal of Waste Electrical and Electronic Equipment (WEEE) for recycling. This is confirmed by the symbol found on the product, user manual or packaging. Through recycling and other forms of processing Waste Electrical and Electronic Equipment, you can make a significant contribution towards helping to protect the environment. [. . . ]