User manual THETA DIGITAL NOVA MACROS RS232

[. . . ] When this parameter is set to OFF, changing inputs powering down/going into standby will maintain all BALANCE menu settings. RS232 Press the SETUP button once, then the A-D button (Page 2 of SETUP), then button # 2, to access the RS232 sub menu, if the optional RS232 feature has been installed. Figure 17A - Front Panel Display of the SETUP Page 2/RS232 Sub Menu Press button # 1 (BAUD) and use the LEVEL UP/DOWN buttons to select the Baud rate that matches that of the RS232 controller. This can be done by selecting a "Status Level", which means if any Casa Nova parameter changes, that level's bytes will be sent to the port. [. . . ] The RESTORE-FACTORY-DEFAULTS section (buttons 3-6) contains 4 options. Press button # 3 (CUR) to restore the factory INPUT parameters (except names) to the currently selected input. Button # 4 allows the user to restore the factory INPUT parameters (except names) to ALL 12 inputs. Pressing button # 5 (GLOB) will restore all global parameters (those that are not stored by input select button). Lastly, button # 6 (NAMES) will restore all 12 Input Select Button names as well as all Input Jack names. The "ARE YOU SURE?" message appears in the display whenever buttons 3-6 are pressed. Names A new feature has been added to all instances of using the Names feature, i. e. When in a submenu to edit a name, pressing the DISPLAY button once will clear the current name completely and put the cursor in the first position. This applies to both LCD and OSD names. RS232 & Macros Addendum 2 Rev 1. 01 6-4-99 Casa Nova Owners Manual Addendum Macros, RS232 and Names Editing Updates Press the SETUP button once, then the A-D button to shift to the second page of the SETUP menu, shown in figure 61. That is to say that when an INPUT SELECT button is pressed or the Casa Nova is powered down/put into standby, any changes will be reset to zero. This feature has an override, which is set by pressing button # 1 and set to OFF. When this parameter is set to OFF, changing inputs will maintain all BALANCE menu settings. Press button # 2 to access the RS232 sub menu, if the optional RS232 feature has been installed. Pressing the A-D button shifts back to the first page of the SETUP menu. Pressing the SETUP button once more returns the OSD to the current INPUT SELECT page. Figure 61 - Video Display of the SETUP Page 2 Menu RS232 Press the SETUP button once, then the A-D button (Page 2 of SETUP), then button # 2, to access the RS232 sub menu, if the optional RS232 feature has been installed. In the RS232 sub menu, press button # 1 (BAUD) and use the LEVEL UP/DOWN buttons to select the Baud rate that matches that of the RS232 controller. Button # 2 allows the user to enable/disable the status output of the RS232 port, and if enabled, the status level. Please refer to page 1 for additional information pertaining to this parameter. Figure 61A - Video Display of the SETUP Page 2/RS232 Sub Menu Pressing the SETUP button twice (if in the RS232 sub menu, once if in SETUP page 2) returns the OSD to the current INPUT SELECT page. RS232 & Macros Addendum 3 Rev 1. 01 6-4-99 Casa Nova Owners Manual Addendum Macros, RS232 and Names Editing Updates Setup Macros From the SETUP/INPUT Page 3 sub menu, press button # 4 once to enter the MACROS sub menu, shown in figure 79. Figure 79 - Video Display of the SETUP/INPUT Page 3/MACROS Sub Menu COPY CURRENT INPUT TO: allows the user to either copy all input parameter values from the currently selected input to another (selectable) ANOTHER INPUT (button # 1), or to ALL INPUTS which is the other 11 inputs (button # 2). [. . . ] Lastly, button # 6 (INPUT AND JACK NAMES) will restore all 12 Input Select Button names as well as all Input Jack names. The "ARE YOU SURE?" message appears in the display whenever buttons 3-6 are pressed. Press SETUP twice to return to the first page of the SETUP menu. Names A new feature has been added to all instances of using the Names feature, i. e. [. . . ]