User manual THETA DIGITAL DREADNAUGHT II

[. . . ] THETA DIGITAL C O R P O R A T I O N Dreadnaught II Owner's Manual REV 1. 02 PREFACE CONGRATULATIONS You have just acquired the most advanced and versatile component for the amplification of audio ever to have been developed. IMPORTANT Save all packaging in a dry place away from fire hazards. Your Dreadnaught II is a precision electronic instrument and should be properly packaged any time shipment is made. In the unlikely event that you have to return your Dreadnaught II to the factory for service, or if you send it to us for updating, the original packaging will best protect the unit from shipping damage. In order to achieve the fullest flexibility and enjoyment from your Dreadnaught II, we at Theta recommend that you read this manual in full before connecting the unit to your audio/video system. [. . . ] When the rear panel STANDBY TRIGGER jack receives a 5-12 VDC pulse the Dreadnaught II will change its mode from either standby to operate, or operate to standby, depending on its current mode. It is recommended that this be left ON at all times during regular use with the exception of whenever cables are connected/disconnected or when the unit is not going to be used for an extended period of time. AC POWER INPUT. 8 OPERATION Before turning on the Dreadnaught II, ensure that all precautions and warnings have been carefully reviewed and adhered to. Damage to the Dreadnaught II caused by improper operation, wiring and/or ventilation will not be covered under warranty and Theta will not be liable for any consequential damage or loss. When first turning on the rear panel power switch, the red STANDBY LED on the front panel will illuminate, indicating that all channels are in standby mode. When in standby, the signal is muted and the output bias of each channel is reduced to approximately 10 percent. The SURROUND LED on the front panel will illuminate green, indicating that all channels, regardless of which buss they are assigned to, will come on when the amplifier is taken out of standby. When in standby, the front panel STANDBY LED will be red and when out of standby, this same LED will be green. The SURROUND button activates/deactivates the channel(s) that been assigned to the surround buss via their rear panel switch. When the surround buss is active, the SURROUND LED on the front panel will illuminate green. When the surround buss is inactive, the front panel SURROUND LED will be off. The surround buss may be turned on or off regardless of whether the unit is in standby or operate. Each module can be assigned to operate on either the STEREO or SURROUND buss. When the Dreadnaught II has more than two modules installed in it, it is recommended that the front left and right channels be set to STEREO and all remaining channels be set to SURROUND, via the rear panel STEREO/SURROUND switch. In the STEREO mode (front panel SURROUND LED off), any channels set to the STEREO buss will operate. In the SURROUND mode (front panel SURROUND LED illuminates green), all channels will operate. Single and Two channel Modules The Dreadnaught II can be loaded with any combination of modules. Each module can be set to operate individually on the stereo or surround buss. Note: The speaker output polarity on the single channel module is reversed compared to the two channel module. The maximum spade lug thickness for the two channel module is 1/16" Remote Triggers When the rear panel STANDBY TRIGGER jack receives a 5-12 VDC pulse, the Dreadnaught II will change its state from either standby to operate, or operate to standby, depending on what the current state is. When the rear panel SURROUND TRIGGER jack receives a 5-12 VDC pulse, the Dreadnaught II's surround buss will change from its current status, either on or off. Use a 1/8" (3. 5mm) mono plug for these jacks. RS232 RS232 is an option in the Dreadnaught II. It can be installed at any time either at the factory or an authorized Theta dealer. [. . . ] 17 5/8" W x 8 7/16" H x 23 1/2" D (448 x 214 x 597 mm) 98 Lbs. Boxed with accessories (50. 4 Kg) Internal: 176° F (80° C) Room: 122° F (50° C) Maximum Operating Temperature: 16 17 90 DAY LIMITED WARRANTY TERMS AND CONDITIONS (3 Year optional extended service contract) 1. Theta Digital Corporation, henceforth referred to as Theta, warrants the product designated herein to be free of manufacturing defects in material and workmanship, subject to the conditions set forth herein, for a period of 90 days from the date of purchase by the original purchaser, henceforth referred to as purchaser. If the purchaser registers the unit with Theta by mailing in the warranty card, together with a copy of the bill of sale, within 14 days of the date of purchase, said purchaser will be registered for an extended service contract. [. . . ]