User manual THETA DIGITAL CNOM202

[. . . ] THETA DIGITAL C O R P O R A T I O N Casa Nova Owner's Manual Digital Done Right TM PREFACE CONGRATULATIONS You have just acquired the most advanced component for the control and processing of audio and video ever to have been developed. IMPORTANT Save all packaging in a dry place away from fire hazards. Your Casa Nova is a precision electronic instrument and should be properly packaged any time shipment is made. In the unlikely event that you have to return your Casa Nova to the factory for service, or if you send it to us for updating, the original packaging will best protect the unit from shipping damage. In order to achieve the fullest flexibility and enjoyment from your Casa Nova, we at Theta recommend that you read this manual in full before connecting the unit to your audio/video system. WARNING United Stated law prohibits disposition of these commodities to Libya, Laos, North Korea, Cambodia or Cuba unless otherwise authorized by the United States. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. [. . . ] In this example, when an LD is being played, the user would press the INPUT SELECT button that is `assigned' to this transport. If RF-1 (or the name assigned to this input jack) is not displayed in the lower right hand corner of the LCD, press the A-D button once. When a CD is to be played in this transport, press the A-D button once to display COAXIAL 1 (or the name assigned to this input jack) in the lower right hand corner of the LCD. The default MODE for this INPUT SELECT jack should be that which is desired for the playback of CD's, as when the Casa Nova detects either a Dolby Digital AC-3 RF or 5. 1 data stream, it will detect this signal and automatically change the MODE to Dolby Digital or DTS. It is important to note that when the Casa Nova auto detects a Dolby Digital or DTS signal and auto switched the mode, this mode is temporary and not stored. If the Casa Nova ceases to detect this signal, it will revert back to the previous mode for the currently selected INPUT SELECT button, in approximately 15 seconds. Press SETUP 3 times then repeatedly press the A-D button to toggle between the input jacks for the currently selected INPUT SELECT button. It is advisable to only map input jacks that will be used, to the currently selected INPUT SELECT button. This will eliminate needless pressing of the A-D button to cycle through unused jacks. Note: When input jacks are re-assigned and the user exits SETUP, the new input jack mappings will not be active until either the A-D button is pressed or another INPUT SELECT button is pressed. Next, map the appropriate video input jacks, if applicable, to the same INPUT SELECT button. In the case of the above example where the RF-1 jack is the first audio jack mapped to the currently selected INPUT SELECT button, either the composite or S-video (whichever type is being used to connect the video signal from the transport to the Casa Nova) input jack must be mapped first in the video search order. Since the LD's audio jack is second in the audio search order, it must also be mapped second in the video search order. Continuing this example, if a source device has both an audio and a video signal associated with it, and the audio signal is third in the audio search order, then its video signal must be third in the video search order. 30 To map a video signal to an INPUT SELECT button, first press the desired INPUT SELECT button, then press SETUP, INP, A-D, SOURCE and A-D once for a composite video signal, or A-D twice for an S-video signal. Press the appropriate button (1-6) which corresponds to the same position in the audio search order menu for this source device and press the LEVEL UP/DOWN button to select the desired video input jack. Press the SETUP button once to return to the SETUP/INP Page 2 submenu. Password for Each INPUT SELECT Button Button # 3 (PW) allows the user to assign a password to the currently selected INPUT SELECT button. Press PW once and the "ARE YOU SURE?" message appears on the LCD. Pressing NO (button # 2) reverts back to the SETUP/INP Page 2 submenu. Pressing YES (button # 1) will display the current submenu, however the password for this INPUT SELECT button will appear above PW (button # 3). The user can use buttons 1-6 to enter a password, or elect to have no password for this INPUT SELECT button by pressing the A-D button 5 times, which will display all zeros, indicating no password. Note: If a zero appears in any position of the password, it will be seen as all zeros, or no password. [. . . ] Operating Temperature: Storage Temperature: Relative Humidity: 32 to 95 F (0 to 35 C) -22 to 167 F (-30 to 75 C) 95% maximum without condensation. Remote Control: 1 hand-held, battery powered control unit uses 2 AAA batteries. Specifications subject to change without notice. 87 90 DAY LIMITED WARRANTY TERMS AND CONDITIONS (5 Year optional extended service contract) 1. Theta Digital Corporation, henceforth referred to as Theta, warrants the product designated herein to be free of manufacturing defects in material and workmanship, subject to the conditions set forth herein, for a period of 90 days from the date of purchase by the original purchaser, henceforth referred to as purchaser. If the purchaser registers the unit with Theta by mailing in the warranty card, together with a copy of the bill of sale, within 14 days of the date of purchase, said purchaser will be registered for an extended service contract. [. . . ]