User manual THERMADOR PH42ZS

[. . . ] Before servicing or cleaning the unit, switch power off at service panel and lock ser vice panel. When the service panel cannot be locked, securely fasten a prominent warning device, such as a tag to the service panel. WARNING TO REDUCE THE RISK OF INJURY TO PERSONS, IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING: a ) SMOTHER FLAMES with a close-fitting lid, cookie sheet, or other metal tray, then turn off the gas burner or the electric element. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT. c) DO NOT USE WATER, including wet dish cloths or towels - a violent steam explosion may result. [. . . ] When activated, the ventilator will turn on low and the corresponding LED will blink, indicating an over temperature condition. While the high temperature sensor is activated, the blower speed can be changed or turned off. When the control sensor reaches 140ºF (60º C), a reset will occur. During reset, the control will revert back to the operational state prior to the high temperature condition. High Temperature Fault Condition - The circuit is equipped with an alarm indicating that the heat sensor protection is not working, due to a damaged sensor. In the case of this extreme condition, the three speed indicator LEDs will start blinking. All the controls will be operational except for the speed indicators. FAN SPEED Pressing button once, from an off state, turns the ventilator on low. Each successive press of the button increases the fan speed until high where the fan cycles back to the low speed. 1 ­ Low 2 ­ Medium 3 ­ High DELAY SHUT OFF · Press to turn fan on high for 10 minutes. If the ventilator is off when the delay button is pressed, the ventilator will turn on to the high speed setting for 10 minutes. If the ventilator is on when the delay button is pressed, the ventilator runs for 10 minutes at the current speed then turns off. · During a timed period, the LED above the Delay Shut Off button is illuminated. · To interrupt a timed period, press Fan Speed or Off button. CLEAN FILTER REMINDER After 40 hours of operation, the clean filter reminder LED above this button will illuminate indicating that the filters need to be cleaned. When this indicator illuminates, clean the filters as instructed on page 6. After cleaning, press this button for 3 seconds to reset the 40-hour period and turn the LED off. LIGHT On/Dim/Off This button controls the halogen lighting. A third press turns the lights off. HEAT LAMP (for Wall Hoods Only) The buttons marked "L" and "R" independently control the left and right infrared heating lamps, turning the lights on or off. PAGE 5 CARE AND CLEANING To Clean Hood Surface · For general care, wipe the outside of the stainless steel with sudsy water or household cleaners such as Fantastic ® or Formula 409 ®, rinse well and dry with a clean soft cloth to avoid water marks. To remove finger prints and give added shine, use spray cleaners such as Stainless Steel Magic® and Shimmer ® . Do not allow any cleaning compounds to remain in contact with stainless steel for extended periods. 1 2 3 ® · · · OFF FAN SPEED DELAY A AY SHUT OFF FILTER L LTER LIGHT Figure 3 NOTE: DO NOT USE COOKTOP WHILE HOOD IS DISASSEMBLED. GREASE TROUGHS MUST BE IN PLACE BEFORE INSTALLING THE ALUMINUM FILTERS. · To Clean Filters and Troughs Your hood has removable aluminum filters, grease troughs and side panels. They must be cleaned when the filter light illuminates on the control panel or whenever they collect the grease. When used over a grill, wok or other high grease applications, more frequent cleaning may be required. To Remove Filters and Grease Troughs: · Turn the fan and lights off. [. . . ] Service by an unauthorized agency, damage or repairs due to service by an unauthorized agency or the use of unauthorized parts. Service visits to: · · · · · · Teach you how to use the appliance. You are responsible for providing electrical wiring and other connecting facilities. Damage caused from accident, alteration, misuse, abuse, improper installation or installation not in accordance with local electrical codes or plumbing codes, or improper storage of the appliance. [. . . ]