User manual THERMADOR 9000001005

[. . . ] · Bosch dishwashers are intended for residential use only, and should not be used in commercial food service establishments. · NEW INSTALLATION - If the dishwasher is a new installation, most of the work must be done before the dishwasher is moved into place. · REPLACEMENT - If the dishwasher is replacing another dishwasher, check the existing dishwasher connections for compatibility with the new dishwasher, and replace parts as necessary. Inspect the Dishwasher After unpacking the dishwasher and prior to installation, thoroughly inspect the dishwasher for possible freight or cosmetic damage. [. . . ] Water that is too hot can cause some detergents to loose effectiveness. The hot water supply pressure must be between 5 - 120 psi (0. 3 - 8. 27 bars). Hot Water Supply Plumbing NOTE: Regardless of where the hot water supply line enters the enclosure (following the guidelines on page 8), position the line 14" (355mm) from the enclosure's left side, as shown in Figure 7, letter A. NOTE: Decide whether braided hose or copper tubing will be used for the hot water supply plumbing, and purchase the correct type of hot water supply shut-off valve, 90° elbow, and necessary fittings for the hot water supply plumbing. Install an easily accessible shut-off valve (not supplied) in the hot water supply line, as shown in Figure 7, letter B. All solder connections must be made before the water line is connected to the dishwasher's water inlet valve. Water may also be supplied to the dishwasher by using a braided hose line. Check with your local plumbing supply sources for the proper hose and 90° elbow fitting. (Continued on next page) Plumbing Preparation 6 B 14" (355mm) A Figure 7 PLUMBING PREPARATION (continued) Drain Plumbing Dishwasher Connection Piece If the dishwasher is to drain either directly into the household drain plumbing or through an air gap, install a dishwasher connection piece under the sink, as shown in Figure 8, letter A. Installing an Air Gap If local ordinances require an air gap, as shown in Figure 9, letter B, install it according to the manufacturer's instructions. Disposer If a disposer is to be installed, as shown in Figure 10, letter C, install it according to the manufacturer's instructions. Whether the disposer is newly installed or existing, remove the disposer's dishwasher drain connection plug. B A Figure 8 ENENENENENGLISH GLISH GLISH GLISH GLISH Figure 9 DISHWASHER PREPARATION Dishwasher preparation involves four tasks: · Installing the Mounting Brackets · Removing the Toe Panel · Installing the 90° elbow fitting · Junction Box Preparation Installing the Mounting Brackets CAUTION: Before installing the supplied mounting brackets (letter E in the Materials Supplied section of this manual), decide which method of securing the dishwasher into its enclosure will be used. Once the mounting brackets are installed on the dishwasher, removing them is difficult and will damage the mounting brackets and the dishwasher. The dishwasher can be secured into its enclosure in two ways: 1) Top Mount is used for countertops made of wood or other materials that can easily drilled. Orient the mounting brackets as shown in Figure 11, letter A, and position the two small tabs on the mounting brackets over the two slots on the dishwasher's front corners. Push the mounting brackets down firmly to insert the tabs into the slots. 2) Side Mount is used for countertops made of marble, granite, or other very hard materials that cannot be easily drilled. Bend the mounting brackets along the small holes and in the same direction as the two small tabs. Adjust the front levelers by turning them with a screwdriver, as shown in Figure 16, letter C. If additional height is needed, shims may be added under the leveler feet. 5) Push the dishwasher into the enclosure. 14" (355mm) 21" (533mm) ENENENENENGLISH GLISH GLISH GLISH GLISH Figure 14 DOOR PANEL INSTALLATION DW44FI Fully Integrated Models - Panel Installation The Thermador Fully Integrated model comes with additional mounting hardware and a template sheet that will show you how to mount the panel. Follow carefully the instructions on the template. A Figure 15 B C Figure 16 9 Placing the Dishwasher SECURING THE DISHWASHER Drive the mounting screws through the holes in the mounting brackets, as shown in Figure 17, letter A for Top Mount, or as shown in Figure 17, letter B for Side mount. A DRAIN HOSE CONNECTION The dishwasher drain hose may be connected to the drain plumbing in one of four ways: 1) Directly to the undersink dishwasher drain connection, as shown in Figure 18. [. . . ] If the dishwasher still does not operate properly, refer to the Customer Service Section of the Use and Care Manual. Figure 23 13 Electrical Connection/Door Tension Adjustment/Base and Toe Panel CUSTOMER SERVICE Your Thermador dishwasher requires no special care other than that described in the Care and Cleaning section of the Use and Care Manual. If you are having a problem with your dishwasher, before calling for service please refer to the Self-Help section of the Use and Care Manual. If service is necessary, contact your dealer or installer or an authorized service center. If you are having a problem with your Thermador dishwasher and are not pleased with the service you have received, please take the following steps (in the order listed below) until the problem is corrected to your satisfaction. [. . . ]