User manual THERMADOR 5060002189C

[. . . ] 2 Cabinet Preparation and Clearances C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2, 3 Junction Box Location D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Countertop Cutout Dimensions E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installing the Cooktop F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] A 24 inch minimum distance is necessary when the bottom of the wood or metal cabinet is protected by not less than 1/4 inch of a flame retardant material covered with not less than No. 28 MSG sheet steel, 0. 015 inch (0. 4 mm) thick stainless steel, 0. 024 inch (0. 6 mm) aluminum, or 0. 020 inch (0. 5 mm) thick copper. Flame retardant materials bear the mark: The cutout dimensions depend upon whether the installation is for replacement, new construction, or installation in a solid surface countertop material, such as SurellTM, Corian® etc. These materials require larger cutouts, use of heat reflective tape and rounded corners. Always consult the countertop manufacturer for specific Installation Instructions. INSTALLING THE COOKTOP !BEFORE TURNING POWER "ON", BE SURE THAT ALL CONTROLS ARE IN "OFF" POSITION. SEAL WITH FOAM TAPE F UNDERWRITERS LABORATORIES INC. CLASSIFIED MINERAL AND FIBER BOARDS SURFACE BURNING CHARACTERISTICS Followed by the flame spread and smoke ratings. , these designations are shown as "FHC (Flame Spread)/ (Smoke Developed)". Materials with "O" flame spread ratings are flame retardant. The minimum horizontal clearance from the sides and back edge of the cooktop to the adjacent vertical combustible walls is 0 Inches. A foam tape is provided to seal the cooktop edges to the countertop, F, (see Page 4). Turn cooktop upside down and apply tape approximately 1/16" from the glass edges to the underside of the cooktop glass. Use tape around the entire glass perimeter cut off excess where tape ends butt. SECURE COOKTOP TO COUNTERTOP G The cooktop should be secured to the countertop using the hold-down brackets provided. Prior to inserting cooktop into cutout, turn cooktop upside down and attach brackets to the burner box using the washers and screws. Insert clamping screw into the bracket and secure cooktop to countertop. Use a wood block to protect fragile countertop materials. PAGE 3 Installation Instructions Models: CET304, CET365, CEP304, CEP365, CEP456 PAGE 4 Installation Instructions Models: CET304, CET365, CEP304, CEP365, CEP456 SOLID SURFACE COUNTERTOPS H ELECTRICAL CONNECTION 1. Connect the cooktop lead wires to the junction box supply wires in proper phase: Always consult the countertop manufacturer for specific instructions. granite and marble) or SOLID SURFACE MATERIALS, such as SurellTM and Corian ® , require special cutout preparation and installation procedures. Round the cutout corners according to instructions from the countertop manufacturer. Apply heat reflective tape (such as Scotch Aluminum Foil Tape #425 or #427) around the cutout so that it folds over the top and side surfaces. Use a wooden block underneath the countertop before tightening the bracket screws. Center cooktop in the cutout to insure adequate clearance between the burner box and countertop edge. (A light pencil mark along the center of front edge and side edge of cooktop and counter will aid positioning of the cooktop in the center. ) 5. [. . . ] Consult with a heating and ventilating engineer for your specific ventilation requirements. For the most detailed information, refer to installation instructions accompanying product or write Thermador indicating the model number. We reserve the right to change specifications or design without notice. Thermador is not responsible for products which are transported from the United States for use in Canada. [. . . ]