User manual THERMADOR 5060000885A

[. . . ] The information in this manual will help you easily operate and care for your cooktop for years of satisfaction. For additional information, visit our website at www. thermador. com or write to us at: Thermador Customer Support Call Center 5551 McFadden Avenue Huntington Beach, CA 92649 Sincerely, Test Kitchen Consumer Scientists CET/CEP Cooktop Care and Use Manual Table of Contents Important Safety Instructions . . . . . . 8 Precautions for Long Life and Good Appearance of the Surface: . . . . . . . . . . . . . . . . 12 Heat Settings for Radiant and Bridge Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The H remains on until the cooking area has cooled to a safe-to-touch temperature. If an H is lit inside the element display, use caution when working or cleaning around the cooktop as the cooktop is still hot. · PRECAUTIONS FOR LONG LIFE AND GOOD APPEARANCE OF THE SURFACE: · Regular, daily care using the Cooktop Cleaning Creme® will protect the surface and make it easier to remove food soil and water spots. The glass ceramic cooking surface is a durable material resistant to impact but not unbreakable if a pan or other object is dropped on it. Do not use aluminum foil directly on the glass; it will melt and damage the glass surface. Do not allow plastic, paper, or cloth to come in contact with the hot glass surface; these items can melt or burn and damage the glass surface. Avoid placing a wok support ring, trivet or other metal stand on the glass surface. Do not slide cookware across the cooking surface; it may scratch the glass. Do not place wet pans on the glass surface. · RETAINED HEAT The glass cooking surface retains heat and stays hot after the element(s) have been turned off. The retained heat may be used to hold foods at serving temperatures for a short time. · · LOCKING THE COOKTOP The Panel Lock is selected to prevent the control pads from being turned on. A beep will sound and the panel lock light stays lit indicating that the cooktop is locked. A beep will sound and the light will go out indicating the cooktop is unlocked. After 10 minutes, the cooktop beeps and shuts down if no pan is placed on the element. The placement of the element control corresponds to the placement of the heating element on the cooktop. On CEP models, ZONE SMARTTM will always be activated when an element is turned on. To turn off ZONE SMART, see Page 11. Using a single element (with ZONE SMART, Pan Sensing Only) 1. Touch the center of the control pad that corresponds to the element desired. The display flashes 0 and two lights to the left and right of the display. The element heats up when it has been turned on and the sensors detect the presence of a pan. Pan Sizing On the double and triple elements, a sensor under the cooktop can choose the size pan being used and turn on the appropriate element. This feature is either on or off for all elements and works together with the Pan Sensing feature. Using a dual or triple element (with ZONE SMART Pan Sensing and Sizing) 1. Touch the center of the control pad that corresponds to the chosen element. The small, medium, or large cooking areas on the selected dual or triple element will be activated automatically depending on the size of the pan. To turn off surface element, touch the element display area twice OR To turn off all elements at the same time, touch the POWER Pad. When the pan is lifted off the element, the heating is interrupted. The number of the selected cook setting and the pan missing symbol ( U ) flashes in the display. [. . . ] Check the power source to see if a fuse has blown or if the circuit breaker tripped. Use a standard single-edge blade for replacement. Element cycles on the highest setting Element cycles more than usual · · · · · A slight odor is noticeable when an element is turned on Flashing control lights · · Cooktop controls will not turn on · · The cooktop has switched itself off Replacement razor blades for the scraper · · HOW TO OBTAIN SERVICE For authorized service or parts information, call 800/735-4328. We want you to remain a satisfied customer. If a problem does come up that cannot be resolved in your satisfaction, please let us know. Write: Thermador Customer Call Center, 5551 McFadden Avenue, Huntington Beach CA 92649 or call 800/ 735-4328. [. . . ]