User manual THERMADOR 5040004761

[. . . ] 4 Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Grounding Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SECTION 4: Unpacking, Moving and Placing the Unit . . . . . . . . . . . . . . . . . . . . . 5 ­ 7 Locating your Char Glo® Barbecue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The appliance must be isolated from the gas supply system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2" psig (3. 5kPa). When checking the manifold gas pressure, the inlet pressure to the appliance regulator should be at least 6. 0" W. C. Do not attempt any adjustment of the pressure regulator. ATTENTION: CAUTION: ATTENTION: L'appareil doit étre isolé du circuit d'alimentation de gaz en fermant son rob1net manuel d'isolement individuel pendant toutes essais sous pression du circuit de tuyauterie d'alimentation de gaz aux pressions d'essai égales à ou moins de 3. 5kPa (1/2 psig). En controlant la pression de gaz du tubulure, la pression de prise au régulateur de l'appareil devrait étre au moins 11. 2mm HG pour gaz naturel, et 20. 5mm HG pour gaz de propane. N'essayez aucun réglage du régulateur de pression. CAUTION: When connecting to propane gas supply, make certain that the propane gas tank is equipped with its own high pressure regulator in addition to the pressure regulator supplied with the appliance. The pressure of the gas at the appliance regulator must not exceed 14" water column. ATTENTION: En se reliant a l approvisionnement de gaz de propane, assurez-vous que le réservoir de gaz de propane est équipé de son Propre régulateur à haute pression en peus du régulateur de Pression fourni avec l'appareil. La pression du gaz au régulateur de l'appareil ne doit pas exéceder 26. 1 mm HG. Page 3 SECTION 3: ELECTRICAL REQUIREMENTS AND GROUNDING INSTRUCTIONS CAUTION Installation of electrical supply circuit should be done by a qualified electrician in accordance with local codes and ordinances. In the absence of local codes or ordinances, the supply should be installed in accordance with the National Electric Code ANSI/NFPA No. The Thermador Char Glo® barbecues use an electronic ignition system that requires a 120 VAC, 15A, 60 Hz power supply. A properly grounded duplex outlet must be provided adjacent to the lower left rear corner of the unit. A properly grounded duplex outlet made for outdoor applications should also be provided above the level of the cooking surface on the left side of the unit. See Figure 2. WARNING Electrical Grounding Instructions This outdoor cooking gas appliance is equipped with a three-prong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug. Figure 2 AVERTISSEMENT Instruction pour la mise a la terre electrique Cet appareil est muni d'une fiche a trots broches (mise a la terre) afin de vous proteger des chocs et doit etre branche directement dans une prise de courant a trots broches adequatement mise a la tem. II ne faut pas couper ou enlever la broche de mise a la tem de cette fiche. BARBECUE Three-Prong Plug and Receptacle Page 4 SECTION 4: UNPACKING, MOVING AND PLACING THE UNIT LOCATING YOUR CHAR GLO® BARBECUE Leaving the unit on the pallet, move the unit close to the final installation site. Unpack and remove all accessory items, packing materials and product literature from inside the unit. If the unit is not compatible with the gas supply, it will be necessary to convert it for use with the supply. See conversion instructions below. CONVERSION KIT BY MODEL Model No. CGB30CZLP Orifice Description Part Number 2. 06mm (#46) Orifice Hood, Grill Burner 5040000445 1. 40mm (#53) Orifice Hood, Infrared Burner 5040000443 Conversion Sticker 5040000623 2. 06mm (#46) Orifice Hood, Grill Burner 1. 40mm (#53) Orifice Hood, Infrared Burner 0. 93mm (#63) Orifice, Smoker Burner Conversion Sticker 2. 06mm (#46) Orifice Hood, Grill Burner 1. 40mm (#53) Orifice Hood, Infrared Burner 0. 93mm (#63) Orifice, Smoker Burner 1. 86mm (#49) Orifice, Side Burner Conversion Sticker 2. 06mm (#46) Orifice Hood, Grill Burner 1. 40mm (#53) Orifice Hood, Infrared Burner 0. 93mm (#63) Orifice, Smoker Burner Conversion Sticker 5040000445 5040000443 5040000431 5040000623 5040000445 5040000443 5040000431 5040006713 5040000623 5040000445 5040000443 5040000431 5040000623 Quantity 2 1 1 3 1 1 1 3 1 1 2 1 4 2 1 1 Remarks To Convert LP To NG CGB36FZLP To Convert LP To NG CGB48FSZLP To Convert LP To NG CGB48FZLP To Convert LP To NG Tools/Parts Required Socket Driver-1/4" Drive, 3" minimum extension 3/16" Or 7 mm Socket or Wrench 1/2" Deep Well Socket 1/2" Open Wrench Phillips Screwdriver Slotted Screwdriver Masking Tape Liquid Propane Conversion to Natural Gas All models are manufactured at the factory for use with LP gas, and as such require conversion for use with an NG gas supply. The conversion should be done by a qualified technician or your gas supplier. Make sure that the unit is disconnected from the gas and electrical supplies. Unbolt the main burners from their attachment at the rear of the burner box and remove. From inside control panel area, locate the brass elbows where the orifices are attached. [. . . ] If any of the flame characteristics noted FIGURE 7 above are observed, check the burner for dirt or residue in the ports, spider webs, etc. , and clean or repair as necessary. INSTALLATION INSTALLER CHECKLIST ELECTRICAL -- Properly grounded receptacle is present for unit and rotisserie motor as necessary. -- The burner box area is free of any packing materials and that the burners, radiants and grates are properly located and installed. -- Burner caps properly positioned and seated on burner bases (Model CGB48FSZLP only). -- Placement of unit. -- Specified clearances maintained to combustible or noncombustible surfaces as applicable. GAS SUPPLY -- Appliance is connected to the proper type of gas supply. [. . . ]