User manual THERMADOR 209902480

[. . . ] The appliance must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code ANSI/ NFPA 70, latest edition. (In Canada, installation must be in accordance with the CAN 1-B149. 1 and . 2 Installation Codes for Gas Burning Appliances and/ or local codes ) This appliance has been tested in accordance with ANS Z21. 1, Standard for Household Cooking Appliances (USA) and in accordance with CANl. l-M81 Interim Reqt #58 Domestic Gas Cooktops (CANADA). WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. [. . . ] · Instructions are based on Standard American cabinets 36" high x 24" deep with a 25" countertop. Provide approximately a 10 square inch opening in the toe kick area or other cabinet area for adequate air inlet to the cabinet. Figure 1 ­ Installed Dimensions (from cooktop edges) Cooktop to front of countertop ­ 0" minimum Dimensions are minimum clearances to combustible materials Plan the installation of the unit so that the power cord, gas shut-off valve and gas pressure regulator are accessible from the front of cabinet. If a drawer is installed directly under the cooktop, its depth (front to back) should be no greater than 15". · NOTICE: All measurements given have to be precisely followed. If nonstandard cabinets are used, make sure they are installed with minimum dimensions shown in fig. to Left Side Wall Cooktop A Cut-out B Cut-out C Corner 30" Models 19-1/8" to 19-7/8" 36" Models 19-1/8 to 19-7/8" 45" Models 19-1/8 to 19-7/8" 28-15/16" to 29-3/8" 30" 34-15/16" to 35-3/8" 36" 43-15/16" to 44-1/2 45" Cutout Dimensions are Underlined D Overall 31" 37" 46" PAGE 2 Page 1 of 4 Revision 10/16/01 SGS/X 45" Cut-Out SGS 45" Cut out SGCS 45" Cut-Out 43 15/16 - 44 1/2 43 5/8 - 44 1/2 19 1/8 - 19 7/8 19 1/8 - 19 7/8 1114. 3mm 475. 6mm Rough-in R/I Tol 18. 71 in 0. 015 in 475. 25 mm 0. 381 mm R/I R/I Tol 2 Screw Washer 18. 725 in 475. 631 mm 43. 585 0. 015 0. 118 0. 034 43. 87 in in in in in 1107. 05 0. 381 2. 9972 0. 8636 1114. 289 mm mm mm mm mm Page 2 of 4 Revision 10/16/01 SGS/X 36" Cut-Out SGS 36" Cut out SGCS 36" Cut-Out 34 15/16 - 35 3/8 34 5/8 - 35 3/8 19 1/8 - 19 7/8 19 1/8 - 19 7/8 886. 7 mm 475. 6mm Rough-in R/I Tol 18. 711 in 0. 015 in 475. 25 mm 0. 381 mm R/I R/I Tol 2 Screw Washer 18. 726 in 475. 631 mm 34. 623 0. 015 0. 118 0. 034 34. 908 in in in in in 879. 43 0. 381 2. 9972 0. 8636 886. 669 mm mm mm mm mm Page 3 of 4 Revision 10/16/01 SGS/X 30" Cut-Out SGS 30" Cut out SGCS 30" Cut-Out 28 15/16 - 29 3/8 28 5/8 - 29 3/8 19 1/8 - 19 7/8 19 1/8 - 19 7/8 733. 1 mm 478. 1mm Rough-in R/I Tol 18. 809 in 0. 015 in 477. 75 mm 0. 381 mm R/I R/I Tol 2 Screw Washer 18. 824 in 478. 131 mm 28. 58 0. 015 0. 118 0. 034 28. 865 in in in in in 725. 9 0. 381 2. 9972 0. 8636 733. 139 mm mm mm mm mm Page 4 of 4 ND SGS 45" Cut out SGS 36" Cut out SGS 30" Cut out With Cook and Vent CW CD OW OD SB BT ND Cutout Width Cutout Depth Overall Width Overall Depth Set Back Backsplash Notch Depth 43 15/16 22 1/8 46 23 5/8 1 1/2 1 1/4 3 34 15/16 22 1/8 37 23 5/8 1 1/2 1 1/4 3 28 15/16 22 1/8 31 23 5/8 1 1/2 1 1/4 3 SGS 45" Cut out SGS 36" Cut out SGS 30" Cut out Without Cook and Vent 43 15/16 - 44 1/2 19 1/8 - 19 7/8 34 15/16 - 35 3/8 19 1/8 - 19 7/8 28 15/16 - 29 3/8 19 1/8 - 19 7/8 SGCS 45" Cut-Out SGCS 36" Cut-Out SGCS 30" Cut-Out 43 5/8 - 44 1/2 34 5/8 - 35 3/8 28 5/8 - 29 3/8 19 1/8 - 19 7/8 19 1/8 - 19 7/8 19 1/8 - 19 7/8 CVS30 CVS36 CVS45 28 5/8 34 5/8 43 5/8 INSTALLING THE COOKTOP 1. Seal the Cooktop Apply the foam tape packaged with the cooktop to underside of the cooktop along the perimeter before installing. Important: For solid surface material installations such as Sure l TM ® and Corian , consult with solid surface manufacturer. Apply heat reflective tape such as Scotch® Aluminum Foil Tape #425 or #427 around the cutout so that it folds over on the top and sides. Attach Brackets to the Cooktop Attach clamps of the hold-down brackets packaged with the cooktop to the rough-in box. Adjust hold-down brackets to desired position and tighten screws to rough-in box. Important: For solid sur face material installations: Insert a wooden block between the end of the screw and the bottom of the countertop. Connect Gas Supply The gas inlet to the unit is located at the right rear of rough-in box. After installing a gas shut-off valve in an easily accessible location under the unit (see Figure 6), install the pressure regulator (supplied) to manifold pipe using Teflon® tape on threads of manifold pipe. To prevent possible damage to the gas pressure regulator, install it after the rough-in box is in its permanent position. CAUTION: Do not attempt any adjustment of the pressure regulator, except conversion to propane. Connect the gas supply line to the unit pressure regulator using a 1/2" flex gas line connector between wall shut-off valve and pressure regulator. (See complete procedure in Figure 6. ) Figure 6 Gas and electrical location. [. . . ] Final Check After electrical connection is complete, place each burner cap in correct sized notched position and check operation of electric igniters. Flame should be blue with no yellow tip. For technical service questions contact Customer Relations at 1 (800) 735-4328. For the most up to date critical dimensions by fax, use your fax handset and call 775-833-3600. [. . . ]