User manual THERMADOR 19-12-201D

[. . . ] When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities. Caution -- To reduce risk of fire and to properly exhaust air, be sure to duct air outside. Do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces or garages. Install this ventilator in accordance with all requirements specified by the manufacturer of your cooktop. [. . . ] · Back to back elbows and "S" turns significantly reduces air flow and are not recommended. · A short straight length of duct at the inlet of the remote blower gives the best delivery. · Transition to round duct as close to the Cook`n'Vent® as possible. 10" round duct 8" round duct 7" round duct 3-1/4" x 14" duct 3-1/4" x l0" duct 6" round duct · The use of flexible metal round duct should only be used when no other duct fitting exists. Limit use to short lengths and do not crush when making corners. STEP 2 PREPARE COUNTERTOP CUTOUT For installation of the Cook'n'Vent® with a Thermador cooktop, refer to Part A and Figure 7. For installation with another brand of cooktop, refer to Part B and Figure 8. For all installations, verify cutouts will clear the inside of the front countertop support rail. The front and rear cutouts must be straight and parallel to the front edge of countertop and the rear backsplash or wall. Assure that the side cutouts are square to the front and rear cutouts. All illustrations and dimensions are based upon standard 24" deep by 36" high American style base cabinets with 25" countertops. When installing laminated or solid surface countertops such as SurellTM and Corian®, be sure to follow the countertop manufacturer's instructions regarding minimum corner radii, reinforcement of corners, etc. For overhead cabinet and cooktop side clearances consult cooktop Installation Instructions. A. INSTALLATION WITH A THERMADOR COOKTOP (FIGURE 7 AND TABLE 3) Provide an opening in the countertop as specified in Table 3. Make sure the distance from the front of the countertop to the front of the cutout is not less than dimension "SB. " Verify that the available flat countertop is greater than dimensions "OW" by "OD. " Make certain the backsplash thickness does not exceed dimension "BT". Page 6 TABLE 3 (in inches) CVS30R/ 36R/ 45R INSTALLATION DIMENSIONS WITH THERMADOR COOKTOPS Cooktop Model No. Cut countertop using dims: CD, CW and SB as defined in Figure 8. The installer will need to have the cooktop installation instructions available to complete the installation. All cooktop dimensions should be verified through measurement prior to cutting the countertop: CCW = Cooktop Cutout Width CCD = Cooktop Cutout Depth COW = Cooktop Overall Width COD = Cooktop Overall Depth with the above dimensions confirmed, determine the cutout size as follows: 1. Find the cutout width, (CW): If CCW is smaller than the CVS cutout width then: Installation CVS30 CVS36 CVVS45 CW 28 5/8 34 5/8 43 5/8 3. 4. 5. If CCW is larger than the CVS cutout width then: CW = CCW See Figure 8 for CVS cutout widths and dimension definitions. Page 8 Figure 9 Countertop Surface C L Point "P" (Center of Rear Cut-line) G Cabinet Back Left Side Right Side F Plumb line to intersection A-A & B-B A B C 30" A E § Receptacle Location Adjustable Within Range Note: Centerlines of Rectangular Duct Shown Cabinet Bottom Shelf CB L CABINET CUT-OUT FOR DUCTWORK D TABLE 4 C 8-3/8 8-3/8 8-3/8 INTERNAL BLOWER VTN600CVR D E F 1/2 9-5/8 26-3/4 3-7/8 13-3/16 26-3/4 8-1/16 17-3/16 26-3/4 G 17-9/16 17-9/16 17-9/16 CVS30R CVS36R CVS45R CVS30R CVS36R CVS45R REMOTE BLOWER VTR600Q OR VTR1000Q C D E F 6-9/16 5-1/16 5-1/16 22-1/4 6-9/16 8-1/2 8-1/2 22-1/4 6-9/16 12-3/4 12-3/4 22-1/4 STEP 3 PREPARE DUCT CUTOUTS IN CABINET A. Drop a plumb-line from Point "P" at the center of the rear countertop cutout. Draw Line AA through this point and parallel to the front of the cabinet. Temporarily set intake and cooktop in place and attach integral blower (or duct transition fitting if a remote blower is installed). Verify that the duct cutouts as marked will match the hardware installation. Make all other cabinet modifications needed to provide proper clearances for drawers or removable shelving. Page 9 B. Where a range of measurements is noted, choose a measurement that allows best clearance from wall studs, floor joists, utilities, or other obstructions. § G 22-1/4 22-1/4 22-1/4 D. [. . . ] Let the blower run several minutes at each speed to evaluate its operation. With the blower running, lower the snorkel to its fully retracted position by pressing the push-button once. The blower will immediately turn off. Figure 12 UP/DOWN Push-button 1 2 3 0 Blower Speed Control Knob D. Check to make sure that the top cap on the snorkel does not catch on the back edge of the cooktop when it is lowered. [. . . ]