User manual THERMADOR 08-04-351C

[. . . ] Installation Instructions for Thermador Char Glo® Outdoor Barbecues Models: CGB30RCULP · CGB36RU CGB48RU · CGB48RSBU Installer: Owner: Please leave these instructions with the unit for the owner. L WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. AVERTISSEMENT: Si l'information dans ce manuel n'est pas suivie exactement, une incendie ou une explosion peut résulter, entrainant des dégats matériels, des blessures ou la mort. Inside Front Cover Contents SECTION 1: Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SECTION 2: Gas Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Natural Gas Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Clearance of 3" at the lower left rear of the unit must be maintained to allow adequate routing of the gas and electrical supply lines. In all installations, do not locate this outdoor cooking gas appliance under unprotected combustible overhead construction. II est interdit d'installer le present appareil au-dessous des surfaces combustibles non protegees. To non-combustible construction Above the cooking surface, a minimum 8" clearance from the sides is required to allow use of the rotisserie motor and skewer. A minimum of 3" clearance from the rear is required to allow proper opening of the hood. Page 6 SECTION 4: ELECTRICAL REQUIREMENTS AND GROUNDING INSTRUCTIONS CAUTION CAUTION Installation of electrical supply circuit should be done by a qualified electrician in accordance with local codes and ordinances. In the absence of local codes or ordinances, the supply should be installed in accordance with the National Electric Code ANSI/NFPA No. The Thermador® Char Glo® barbecues use an electronic ignition system that requires a 120 VAC, 15A, 60 Hz power supply. A properly grounded duplex outlet must be provided adjacent to the lower left rear corner of the unit. A properly grounded duplex outlet made for outdoor applications should also be provided above the level of the cooking surface on the left side of the unit. See Figure 2 (Page 5). WARNING Electrical Grounding Instructions This outdoor cooking gas appliance is equipped with a three-prong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug. Figure 2A AVERTISSEMENT Instruction pour la mise a la terre electrique Cet appareil est muni d'une fiche a trots broches (mise a la terre) afin de vous proteger des chocs et doit etre branche dire~ement dans une prise de courant a trots broches adequatement mise a la tem. II ne faut pas couper ou enlever la broche de mise a la tem de cette fiche. BARBECUE Three-Prong Plug and Receptacle Page 7 SECTION 5: UNPACKING, MOVING AND PLACING THE UNIT LOCATING YOUR CHAR GLO® BARBECUE Leaving the unit on the pallet, move the unit close to the final installation site. Unpack and remove all accessory items, packing materials and product literature from inside the unit. If the unit is not compatible with the gas supply, it will be necessary to convert it for use with the supply. See conversion instructions below. CONVERSION KIT BY MODEL Model No. 7. From behind the unit, remove the louvered cover on the infrared rotis burner housing. On Model CGB48RSBU, convert the side burners for LP operation as follows: A. Use a 7mm hex socket on a 3" ratchet extension and apply a piece of tape to the socket to hold the orifice in the socket while removing. NOTE: Install the conversion sticker (supplied) beside the rating label. Page 8 SECTION 5: UNPACKING, MOVING AND PLACING THE UNIT TAPE 9. On all models, the bypass jet must be turned clockwise with a small flat-bladed screwdriver until fully seated to set proper low flow rate. Models CGB36RU, CGB48RU and CGB48RSBU are equipped with a pressure regulator that is permanently mounted within the cart. Using a flat blade screwdriver, remove the cap on the top of the regulator and turn the cap over so that the letters LP are exposed. See Figures 6 and 6A, below. Page 9 SECTION 5: UNPACKING, MOVING AND PLACING THE UNIT 11. [. . . ] See Figure 7. SIDE PANEL INSTALLATION If the unit will be freestanding, accessory panel kits are available. Install the side panels, side shelves and rear panel per the instructions provided in the kit. Lock the caster brakes when not moving the unit. Page 11 SECTION 6:TEST AND ADJUSTMENT CHECKING FOR LEAKS All points of connection to the gas supply should be manifold. It is also advisable to recheck them Tighten any leaking fittings, turn on the gas and periodically. [. . . ]