User manual TERRATEC DVD5.1

[. . . ] English Manual Version: 01. 02. 02 CE Declaration We: TerraTec Electronic GmbH, Herrenpfad 38, D-41334 Nettetal, Germany hereby declare that the product: TerraTec DVD 5. 1 to which this declaration refers is in compliance with the following standards or standardizing documents: · · · · EN 50013 EN 50022 EN 60065 EN60825-1 + A11 The following are the stipulated operating and environmental conditions for said compliance: Residential, business and commercial environments and small-company environments. This declaration is based on: Test report(s) of the EMC testing laboratory TerraTec® ProMedia, SoundSystem Gold, SoundSystem Maestro, SoundSystem Base 1, SoundSystem DMX, SoundSystemDMX XFire 1024, AudioSystem EWS®64, AudioSystem EWS88, AudioSystem EWX24/96, XLerate, XLerate Pro, Base2PCI, TerraTec 128iPCI, TerraTec 512i digital, TerraTV+, TerraTV Radio+, TerraTValue, VideoSystem Cameo 600 DV, WaveSystem, TerraCAM USB, TerraCAM USB Pro, TerraCAM iLook, m3po, Phono PreAmp, MIDI Smart and MIDI Master Pro are trademarks registered by TerraTec® Electronic GmbH Nettetal, Germany. In most cases, the designations used in this handbook for software and hardware are also registered trademarks and are thus subject to the relevant regulations. Meticulous care has been exercised in the preparation of all text passages and illustrations in this User Guide. [. . . ] Alternatively, you can also connect the digital AC-3 output of the player to a suitable input of your playback device. If you aren't sure which input on your amplifier is the correct one, please consult its manual. When you switch the DVD 5. 1 on (see page 35), the TV screen will display the welcome screen (TerraTec logo) and the message ("Loading"). If you have not yet put a CD in the player, it will point this out to you with the words "No disc". Press the button on the device marked CLOSE/OPEN and insert a CD (DVD, etc. ) with the writing facing upwards and press the button again to close the tray. The player will start loading again, recognizing the CD contents automatically, and will start the playback after a few seconds. Use the arrow buttons on the lower section of the remote control for navigation (i. e. Pressing the RETURN button activates the marked position. 38 DVD 5. 1 (English) Basic settings (Setup). You should configure a few basic settings before playing your first CD. The DVD 5. 1 supports multiple languages to display various kinds of information. The following instructions refer to the English menu which is selected by default. The following screen will appear: Move the selection to one of the following areas: OSD MENU AUDIO SUBTITLE This is the language of the on-screen display that you are currently seeing. This is the standard language for the menus (welcome screens) of DVDs. This is the standard language for DVD subtitles. Select the language you prefer. You can navigate through the selections using the left-right buttons of the remote control. Select EXIT to close the menu, or confirm your selection with the Return button on your remote control. DVD 5. 1 (English) 39 Screen setup. The following screen will appear (enlarged): TV TYPE You can choose from three different screen formats. A distorted picture will result if both devices are not using the same setting. OPEN and CLOSE toggles the screen saver (appears automatically after about 10 minutes of inactivity). Select the video output that you're using to connect the player to your TV set here. Closes the menu (if you can't see RETURN, navigate further down with the arrow buttons). SCRN SAVER TV SYSTEM BRIGHTNESS CONTRAST VIDEO OUT RETURN 40 DVD 5. 1 (English) Audio setup. The following screen will appear: OUTPUT Select your preferred (and already cabled) audio output configuration. 2 CH (stereo analog), 5. 1 (for 6-channel playback), SPDIF/PCM (stereo digital) or SPDIF/RAW for AC3 or DTS signals via the digital output. [. . . ] Press the button again to set an end point and the playback will start again from the point at which 44 DVD 5. 1 (English) you first pressed it. If you know the number of a chapter, you can access it directly by pressing the SEARCH button on the remote control. Enter the numbers on the numeric keypad and confirm the entry with RETURN. Press the ZOOM button during playback to zoom into the picture in four stages. [. . . ]