User manual TELEFUNKEN TX 101

[. . . ] Whether this is your first chartplotter, or if you have other TELEFUNKEN equipment, the TELEFUNKEN organization is committed to ensuring you your enjoyment of this chartplotter. TELEFUNKEN technical support personnel stand behind every product we sell, and our Product Support team invite you to contact us should you require technical advice or assistance, at 562-404 -2700 We appreciate your purchase of the GPS CHART 160/ GPS CHART 170C, and encourage you to read this manual throughly, to learn and understand the capabilities of the GPS CHART 160/ GPS CHART 170C fully. Electronic charts displayed by the chartplotter are believed to be accurate and reliable, but they are not intended to be a substitute for the official charts which should remain your main reference for all the matters related to the execution of a safe navigation. For this reason we would like to remind you that you should carry on board and use the officially published and approved nautical charts. [. . . ] If, after 15 minutes, the chartplotter does not get the fix, turn it Off and On again. If, after pressing 'PWR' (for at least 3 seconds) the chartplotter does not turn Off, turn Off the voltage. If the problem persists, erase the memory or remove power from the battery. The GPS Antenna may not be in a open sky position or the antenna cable may not be properly connected. The chartplotter screen becomes very dark after a long exposure to direct sunlight. The fix position is not received within 5 minutes from the power on despite the GPS Status page displays satellites. 1 GENERAL Power consumption (TX 101) : 380mA max @12V Power consumption (CP 170C): 800mA max @12V Power supply (TX 101) : 10 - 35 Volt dc, 5 Watt max Power supply (CP 170C) : 10 - 35 Volt dc, 10 Watt max Interface : Input/Output Interface NMEA-0183 Display (TX 101) : Mono transflective LCD (active area 5, 7") Display (CP 170C) : TFT Color LCD (active area 5, 7") sunviewable tecnology Display Resolution : 320 x 240 pixels Cartography : Operating temperature range : 0/+55 degrees Celsius Storage temperature : -20/+70 degrees Celsius Water Resistence : splash-proof Memory : Non volatile with battery backup Keyboard : Silicon rubber, backlight Weight : 900 gr. 1 Physical Constructions Physical Constructions : Polycarbonate radome, connector for easy mount, rubber-O-ring between top radome and base for waterproof. : Roof-mount with double threaded bolt or flag-pole mount with plastic adapter tubing that converts its base into 1'-14 threaded cap. 1 SYSTEM TEST If you have connected your chartplotter according to the instructions, and chosen the proper menu selection for your device, and are still having problems with your chartplotter, the extended auto-test should help determine the problem. 1 - System Test Use the ShuttlePoint knob to select the desired test. About (page) Selects a page that gives information on software and cartography version and general software specification (as User Points, Routes and so on). " + 'ENTER' Active Track Selects the number of the active Track. 'MENU' + "TRACK" + 'ENTER' + "ACTIVE TRACK" + 'ENTER' Additional Second Factor (ASF) Sets the ASF for the slave in the selected chain. 'MENU' + "ADVANCED SETUP" + 'ENTER' Alarms (menu) Turns Off or sets the desired value for the Arrival Alarm, XTE Alarm, Depth Alarm, Anchor Alarm e Audible Alarm. 'MENU' + "ADVANCED SETUP" + 'ENTER' + "ALARMS" + 'ENTER' Alter = Alternate Solution Turns On/Off the Alternate Solution in the chain. 'MENU' + "ADVANCED SETUP" + 'ENTER' + "NAVIGATE" + 'ENTER' + "COORDINATE SYSTEM" + 'ENTER' + "TD" + 'ENTER' + "Alter" + 'ENTER' Altitude (Unit) Sets the altitude unit among Ft = Feet, FL = Flight Level and Mt = Meters. 'MENU' + "GENERAL SETUP" + 'ENTER' + "UNITS OF MEASURE" + 'ENTER' + "ALTITUDE" + 'ENTER' Anchor Alarm This function allows inserting of the limit of anchor dragging: beyond that, the alarm is activated. The chartplotter computes the distance between the current GPS position and the GPS position saved at the activation of the anchor alarm in the menu. If the computed distance exceeds the value set in the menu, the chartplotter shows the alarm message and starts the acoustic alarm. 'MENU' + "ADVANCED SETUP" + 'ENTER' + "ALARMS" + 'ENTER' + "ANCHOR ALARM" + 'ENTER' Arrival Alarm Specifies the radius of a circle around the Waypoint of a Route: when your vessel reaches this circle the alarm sounds. 'MENU' + "ADVANCED SETUP" + 'ENTER' + "ALARMS" + 'ENTER' + "ARRIVAL ALARM" + 'ENTER' Arrival Time The estimated time of day you will reach your destination, based on your current speed and track from GPS. [. . . ] A line connects such points and represents the past course, called the Track of the ship. Active Track selecting: 'MENU' + "TRACK" + 'ENTER' + "ACTIVE TRK" + 'ENTER' Track storing ON/OFF: 'MENU' + "TRACK" + 'ENTER' + "TRACKING" + 'ENTER' Visible ON/OFF: 'MENU' + "TRACK" + 'ENTER' + "VISIBLE" + 'ENTER' Step unit selection: 'MENU' + "TRACK" + 'ENTER' + "STEP UNIT" + 'ENTER' Deleting Track : 'MENU' + "TRACK" + 'ENTER' + "CLEAR" + 'ENTER' + "YES" + 'ENTER' Track line pattern selecting: 'MENU' + "TRACK" + 'ENTER' + "LINE PATTERN" + 'ENTER' Only for CP 170C: Track Color selecting: 'MENU' + "TRACK" + 'ENTER' + "COLOR" + 'ENTER' Tracking Turns On/Off the Track storing. It is not possible to use the Track storing if you are not receiving a valid fix. 'MENU' + "TRACK" + 'ENTER' + "TRACKING" + 'ENTER' Tracks & Routes Turns On/Off the displaying of Tracks and Routes (recommended and established Routes for ships at sea, including traffic separation schemes, deep water Routes, . [. . . ]