User manual TELEFUNKEN TF 62

[. . . ] ) for use in personal computers (PC) for installation in homes, offices, schools, computer rooms, and similar locations. The suitability of this product for other PC or embedded non-PC applications or other environments, such as medical, industrial, alarm systems, test equipment, etc. Intel Corporation may have patents or pending patent applications, trademarks, copyrights, or other intellectual property rights that relate to the presented subject matter. The furnishing of documents and other materials and information does not provide any license, express or implied, by estoppel or otherwise, to any such patents, trademarks, copyrights, or other intellectual property rights. [. . . ] In addition to the standby power indicator, the board contains three LEDs that indicate the following: • • • The processor LED indicates an elevated temperature on the processor that could effect performance The Voltage Regulator LED indicates an elevated temperature in the processor voltage regulator circuit that could effect performance The hard drive LED indicates SATA drive activity 35 Intel Desktop Board DP55SB Technical Product Specification Figure 7 shows the location of these additional LEDs. 15 Onboard Power Button The board provides a power button that can be used to turn the computer on or off. This button is intended for use at integration facilities to provide the ability to power on/off the board without the need to attach a front panel switch (the onboard power button duplicates the functionality of the front panel button and functions in exactly the same manner). The power button on the front panel is recommended for all other instances of turning the computer on or off. To turn the computer off using the onboard power button, keep the button pressed down for three seconds. Location of the Onboard Power Button CAUTION Electrostatic discharge (ESD) can damage components. The onboard power button should be used only at an ESD workstation using an antistatic wrist strap and a conductive foam pad. If such a station is not available, some ESD protection can be provided by wearing an antistatic wrist strap and attaching it to a metal part of the computer chassis. 0, E-Standby, and ErP Compliance The US Department of Energy and the US Environmental Protection Agency have continually revised the ENERGY STAR requirements. Intel has worked directly with these two governmental agencies in the definition of new requirements. Com/go/energystar Intel Desktop Board DP55SB also meets the following international program requirements in combination with an appropriately efficient power supply: • • Korea E-Standby by meeting the Energy Star 4. Back Panel CIR Emitter (Output) Header Pin 1 2 3 4 5 6 Signal Name Emitter out 1 Emitter out 2 Ground Key (no pin) Jack detect 1 Jack detect 2 Table 21. 2 • Add-in Card Connectors The board has the following add-in card connectors: PCI Express 2. 3 • Power Supply Connectors The board has the following power supply connectors: Main power – a 2 x 12 connector. This connector is compatible with 2 x 10 connectors previously used on Intel Desktop boards. The board supports the use of ATX12V power supplies with either 2 x 10 or 2 x 12 main power cables. When using a power supply with a 2 x 10 main power cable, attach that cable on the rightmost pins of the main power connector, leaving pins 11, 12, 23, and 24 unconnected. This connector provides power directly to the processor voltage regulator and must always be used. Auxiliary PCI Express graphics power connector (SATA style) – this connector provides the required additional power when using high power (75 W or greater) add-in cards in either or both the PCI Express x16 and the PCI Express x8 bus add-in card connectors. €¢ • CAUTION If high power (75 W or greater) add-in cards are installed in either or both the Secondary PCI Express x16 and the PCI Express x4 bus add-in card connectors, the Auxiliary PCI Express graphics power connector must be used. 3 V -12 V Ground PS-ON# (power supply remote on/off) Ground Ground Ground No connect +5 V +5 V +5 V (Note) Ground (Note) Note: When using a 2 x 10 power supply cable, this pin will be unconnected. 4 Front Panel Header This section describes the functions of the front panel header. [. . . ] 1 • • • • • This section contains the following regulatory compliance information for Intel Desktop Board DP55SB: 5. 1 Safety Standards Intel Desktop Board DP55SB complies with the safety standards stated in Table 37 when correctly installed in a compatible host system. 2 European Union Declaration of Conformity Statement We, Intel Corporation, declare under our sole responsibility that the product Intel® Desktop Board DP55SB is in conformity with all applicable essential requirements necessary for CE marking, following the provisions of the European Council Directive 2004/108/EC (EMC Directive) and 2006/95/EC (Low Voltage Directive). The product is properly CE marked demonstrating this conformity and is for distribution within all member states of the EU with no restrictions. [. . . ]