User manual TELEDEX DIAMOND

[. . . ] The plastic overlay slips into place by hooking the tabs on the overlay into the recessed slots located on both sides. -- The overlay is easiest to insert when; The left or right side tabs are inserted first, and the middle part of the overlay is slightly bowed to allow for insertion of the other tabs. To use the DATA PORT: Insert the modular line cord from your fax machine, modem, etc. , into the jack labeled DATA. ADJUSTING THE RING VOLUME The Diamond has two ring volume settings. To change the ring volume: Locate the adjustment control on the back of the telephone labeled RINGER LOW/HI. Slide the switch to the desired LOW or HI ring volume. HANDSET VOLUME The handset has three volume levels. [. . . ] If advance notice is not feasible, the telephone company must; promptly notify you of such temporary discontinuance; afford the opportunity to correct the condition; inform you of your rights to bring a complaint to the FCC under their rules. 6. Repairs to the device may be made only by the manufacturer or an authorized service agency. If unauthorized repair is performed, registration, connection to the telephone lines and remainder of warranty period all become null and void. This equipment is hearing aid compatible. RMA PROCEDURES The following procedure should be followed with all Teledex telephone products prior to sending the telephone to the factory for repair. For two line products, please ensure that one of the line buttons is pressed (if both line buttons are in the UP position, the telephone will not operate). If the steps listed above do not provide a remedy for the suspect telephone, please place a tag on the individual telephone describing the defect. Next, call the Teledex Repair Department at (408) 574-2670, or (408) 574-2172 for an RMA number. SHIPPING INSTRUCTIONS: Please print the RMA number clearly on the outside of your shipping carton(s). Please ship to the following address: Teledex Corporation / RMA#___________ 6311 San Ignacio Avenue San Jose, CA 95119 FREIGHT CHARGES: The Customer is responsible for shipping products for repair to Teledex. After repair, Teledex will return telephone products to the Customer freight prepaid in the same manner in which is was sent (i. e. Freight sent to Teledex UPS Blue, will be returned via 2 day shipping). **Please note: When telephones are returned for repair due to misuse (i. e. liquid spills, abuse, or Customer modification - warranty label broken), the Customer will be charged the standard repair fee, regardless of warranty status. REQUIREMENTS OF PART 15 - FCC RULES NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is not a guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Relocate the telephone with the respect to the receiver. Any changes made by the user not approved by the manufacturer can void the user's authority to operate the telephone. INDUSTRY OF CANADA REQUIREMENTS Notice: The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements documents. The department does not guarantee the equipment will operate to the users satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. [. . . ] Turn the Diamond over (use a non abrasive surface) so the back side is up, facing you. Locate the mounting bracket, and firmly push back and pull up to remove. Rotate the mounting bracket a half turn (180 degrees) so that the mounting eyelet is facing in the same direction as the mounting eyelet located on the bottom surface of the telephone. Insert the top two retaining tabs of the mounting brackets into the mounting bracket slots located near the middle of the telephone , then firmly push down and insert the retaining tabs on the opposite side. [. . . ]